background image

17

PLUG AND PLAY

Plug & Play DDC2B Feature  

This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC 
STANDARD. It allows the monitor to inform the host system of its identity and, depending on 
the level of DDC used, communicate additional information about its display capabilities.  
The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request 
EDID information over the DDC2B channel.

THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO 
INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE 
MUST BE A VIDEO INPUT SIGNAL.

This monitor meets the Green monitor standards as set by the Video Electronics Standards 
Association (VESA) and The Swedish Confederation Employees (NUTEK). This feature is 
designed to conserve electrical energy by reducing power consumption when there is 
no video-input signal present. When there is no video input signal this monitor, following 
a time-out period, will automatically switch to an OFF mode. This reduces the monitor's 
internal power supply consumption. After the video input signal is restored, full power is 
restored and the display is automatically redrawn. The appearance is similar to a "Screen 
Saver" feature except the display is completely off. The display is restored by pressing a key 
on the keyboard, or clicking the mouse.

USING THE RIGHT POWER CORD :  

The accessory power cord for the Northern American region is the wallet plug with NEMA 
5-15 style and is UL listed and CSA labeled. The voltage rating for the power cord shall be 125 
volts AC. 
Supplied with units intended for connection to power outlet of personal computer: Please 
use a cord set consisting of a minimum No. 18 AWG, type SJT or SVT three conductors flexible 
cord. One end terminates with a grounding type attachment plug, rated 10A, 250V, CEE-22 
male configuration. The other end terminates with a molded-on type connector body, rated 
10A, 250V, having standard CEE-22 female configuration. 
Please note that power supply cord needs to use VDE 0602, 0625, 0821 approval power cord 
in European counties. 

 

Summary of Contents for PZN2710Q




























Reviews: