background image

 

60fps Full HD IR IP Camera with Remote Focus and Zoom   

ICA-4210P

 

program cannot detect device over a router. 

z

 

If IP address is not assigned to the PC running PLANET IP 
Wizard II program, then PLANET IP Wizard II program cannot 
find device. Make sure that IP address is assigned to the PC 
properly. 

z

 

Antivirus software on the PC might interfere with the setup 
program. Disable the firewall of the antivirus software during 
setting up this device. 

z

 

Check the firewall setting of your PC or Notebook. 

Internet Explorer does not seem to 
work well with the device 

Make sure that your Internet Explorer is version 6.0 or later. If you 
are experiencing problems, try upgrading to the latest version of 
Microsoft’s Internet Explorer from the Microsoft webpage. 

PLANET IP Wizard II program fails 
to save the network parameters.   

Network may have trouble. Confirm the parameters and connections 
of the device.   

UPnP NAT Traversal

 

Cannot work with NAT router 

Maybe NAT router does not support UPnP function. Please check 
user’s manual of router and turn on UPnP function. 

Some IP cameras are working 
while others failed 

Maybe too many IP cameras have been installed on the LAN, and 
then NAT router is out of resource to support more cameras. You 
could turn off and on NAT router to clear out of date information 
inside router. 

Access this device

 

Cannot access the login page and 
other web pages of the Internet 
Camera from Internet Explorer 

 

 

z

 

Maybe the IP Address of the Internet Camera is already being 
used by another device or computer. To confirm this possible 
problem, disconnect the Internet Camera from the network first, 
and then run the PING utility to check it out.   

z

 

Maybe due to the network cable. Try correcting your network 
cable and configuration. Test the network interface by connecting 
a local computer to the Internet Camera via a crossover cable.   

z

 

Make sure the Internet connection and setting are ok. 

Make sure to enter the IP address of Internet Explorer correctly. If 
the Internet Camera has a dynamic address, it may have 
changed since you last checked it. 

z

 

Network congestion may prevent the web page from appearing 
quickly. Wait for a while. 

The IP address and Subnet Mask of the PC and Internet Camera 
must be in the same class of the private IP address on the LAN. 

z

 

Make sure the http port used by the Internet Camera, default=80, 
is forwarded to the Internet Camera’s private IP address. 

z

 

The port number assigned in your Internet Camera might not be 
available via Internet. Check your ISP for available port. 

z

 

The proxy server may prevent you from connecting directly to the 
Internet Camera, set up not to use the proxy server. 

z

 

Confirm that Default Gateway address is correct. 

z

 

The router needs Port Forwarding feature. Refer to your router's 

Summary of Contents for ICA-4210P






























































































Reviews: