background image

 

60fps Full HD IR IP Camera with Remote Focus and Zoom   

ICA-4210P

 

Chapter 3.  Web-based Management 

This chapter provides setup details of the Internet Camera’s Web-based Interface.

 

3.1 Introduction

 

The Internet Camera can be configured with your Web Browser. Before configure, please 
make sure your PC is under the same IP segment with Internet Camera. 

3.2 Connecting to Internet Camera 

A. Use the following procedure to establish a connection from your PC to the Internet Camera. 

B. Once connected, you can add the camera to your Browser’s Favorites or Bookmarks. 

 

Start the web browser on the computer and type the IP address of the camera. 
The Default IP: “

http://192.168.0.20

“ 

 

 

The login window of Internet Camera will appear,   
Default login 

username and password

 are both 

admin

.

   

 

 

 

 

If the user name and password have been changed with PLANET IP 
Wizard II, please enter the new user name and password here. 

 

After logging on, you should see the following messages at the top of Internet 
Explorer: 

 

Summary of Contents for ICA-4210P






























































































Reviews: