background image

                                                                                                 

Appendix C: Bandwidth and Video Size 

Estimation  

The frame rate of video transmitted from the IR IP Camera depends on connection bandwidth 
between client and server, video resolution, codec type, and quality setting of server. Here is a 
guideline to help you roughly estimate the bandwidth requirements for your IR IP Camera.   

The required bandwidth depends on content of video source. The slow motion video will 
produce smaller bit rate generally and fast motion will produce higher bit rate vice versa.  
Actual results generated by the IR IP Camera may be varying.   

Image Resolution 

Average range of Data Sizes 

for JPEG mode 

Average bit rate for MPEG4 mode 

160 x 120 (QQVGA) 

3 ~ 6k byte per frame 

64kbps~384kbps @ 30fps 

320 x 240 (QVGA) 

8 ~ 20k byte per frame 

128kbps~768kbps @ 30fps 

640 x 480 (VGA) 

20 ~ 50K byte per frame 

256kbps~4096kbps @ 30fps 

 

Note:

 Audio streaming also takes bandwidth around 5 kbps to 64kbps. Most 

xDSL/Cable modem upload speeds may not even reach up to 128 kbps. Thus, 
you may not be able to receive any video while streaming audio on a 128 kbps or 
lower connection. Even though the upload speed is more than 128kbps, for 
optimal video performance, disabling audio streaming will get better video 
performance. 

 

MJPEG  

 

 

 

Resolution 

Quality setting 

fps setting 

Current stream 

Current fps 

320*240 CIF 

Best 

5 fps 

around 2300Kbps 

5 fps 

320*240 CIF 

Best 

15 fps 

around 6700Kbps 

14.7fps 

320*240 CIF 

Best 

25 fps 

around 14300Kbps

28 fps 

320*240 CIF 

Normal 

5 fps 

around 400Kbps 

4.2 fps 

320*240 CIF 

Normal 

15 fps 

around 1200Kbps 

13 fps - 14 fps

320*240 CIF 

Normal 

25 fps 

around 1700Kbps 

30fps 

320*240 CIF 

Lowest 

5 fps 

around 350Kbps 

4.2 fps 

320*240 CIF 

Lowest 

15 fps 

around 1100Kbps 

13 - 14fps 

320*240 CIF 

Lowest 

25 fps 

around 2000Kbps 

25 fps 

 

 

 68 

Summary of Contents for ICA-108













































































Reviews: