background image

18

FCC Statement

NOTE: This equipment has been tested and found to comply with the 
limits for a Class A digital device, pursuant to part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against 
harmful interference when the equipment is operated in a commercial 
environment. This equipment generates, uses, and can radiate radio 
frequency energy and, if not installed and used in accordance with 
the instruction manual, may cause harmful interference to radio 
communications. Operation of this equipment in a residential area 
is likely to cause harmful interference in which case the user will be 
required to correct the interference at his own expense.

ISEDC Statement

CAN ICES-003(A) / NMB-003(A)
This device complies with Industry Canada license-exempt RSS 
standard(s).
Operation is subject to the following two conditions: (1) this device 
may not cause interference,

 

and (2) this device must accept any 

interference, including interference that may cause undesired

 

operation 

of the device.
Le present appareil est conforme aux CNR d'Industrie Canada 
applicables aux appareils radio

 

exempts de licence. L'exploitation est 

autorisee aux deux conditions suivantes: (1) l'appareil ne

 

doit pas 

produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout 
brouillage

 

radioelectrique subi, meme si le brouillage est susceptible 

d'en compromettre le fonctionnement.

CE Mark Warning

This device is compliant with Class A of CISPR 32. In a residential 
environment this equipment may cause radio interference.

Summary of Contents for IPOE-171-60W





















Reviews: