background image

PLANET Mesh Network Manager Guide 

 

 

 

 

As mentioned previously, the NMS use the SNMP method to read the data. Hence if the data 

is failed to load, you may check the SNMP Community or Passwords. The two small circles 

on the top of the table indicate the status of the table. If the green circle is light up, it shows 

the table is loaded completely; if the orange circle is light up, it means the table is loading the 

data, else if the circle to turn to red color, it indicates that the data loading is failed. 

 

 

 

On the other hand, the bar chart at the bottom of the table displaying the signal strength (in 

RSSI) between the selected AP and all its neighbour nodes. The scale of the chart can be 

enlarged by dragging the desired range of x-axis. Drag backward to reset the chart. 

4.2.3.21  Client Properties 

The client properties panel is located at the other side of the map container. In order to initiate 

the NMS to download the client details, hit on the 

Start 

button at the bottom of the panel.  In 

case if there is more than one map is running, a menu would popup to prompt user to select 

which map to be targeted. Once selected, the scanning will be started instantly.  

 

PLANET Mesh Network Manager Guide 

Page40 of 124

Summary of Contents for MAP-3100





























































































































Reviews: