- 1 -
- 2 -
- 3 -
- 4 -
1. Package Contents
The package should contain the following items plus the VIP-1000PT/T. If any item is
missing or damaged, please contact the seller immediately.
Quick Installation
Guide
Handset
Handset
Cord
RJ45 Cable Power Adapter
(VIP-1000T only)
Stand
2. Hardware Installation
Step 1. Handset Connection
Insert one end of the Handset Cord into Handset and the other end into Handset Jack.
Handset
Step 2a. Connecting Power Adapter and Network
Power Adapter (VIP-1000T only)
Network
Switch
Note
Use only the DC 5V 1A power to ensure correct functionality.
Step 2b. Connecting Power via PoE Interface and Network
The VIP-1000PT can be configured without external power if connected to an IEEE802.3af/
at PSE device such as 802.3af/at PoE injector/hub or 802.3af/at PoE switch.
PoE Switch
Note
Only the VIP-1000PT supports 802.3af/at power injection; use of any non-
standard PoE injector could damage the device.
Step 3. Computer Network Setup
Set your computer’s IP address to 172.16.0.x, where x is a number between 2 and 254
(except 1 which is being used for the camera by default). If you don’t know how to do
this, please ask your network administrator.
PC
Step 4. Login Prompt
Use web browser (Internet Explorer 8.0 or above) to connect to 172.16.0.1 (type this
address in the address bar of web browser). You’ll be prompted to input user name and
password: admin and 123, respectively. If you lose an IP of the VIP-1000PT/T, please
refer to the description below to get the IP via panel button.
****
Choose
Start IVR
VIP-1000PT/T
0 Check Status
9 Web Access Port
8 WAN Port Login
7 Reboot
6 Factory Reset
5 DNS
4 Gateway
3 WAN Port Subnet Mask
2 WAN Port IP Address
1 WAN Port Connection
3. IVR Descriptions
Below is the table that lists commands, and descriptions:
Operation
Code
Contents
1
1) Pick up phone and press
‘****’
to start IVR.
2) Choose
‘1’
and the VIP-1000PT/T reports on the current
WAN port
connection type
.
3) At the prompt,
please enter password
. User needs to key-in the pound
sign
‘#’
at the end of the password if he wants to configure the WAN port
connection type.
The password for IVR is the same as the one of Web login. User
can use the phone keypad to enter password directly, and follow the
instructions under
Notice
below.
For example, Web login password is
‘admin’
, so password for IVR is
‘admin’, too. User needs to input ‘23646’ to access and then configure
the WAN connection port.
4) Report
‘operation successful’
if password is right.
5) Choose the new WAN port connection type from 1.DHCP and 2.Static (end
with
‘#’
).
6) Report
‘operation successful’
if user makes the changes successfully.
Then the VIP-1000PT/T will return with the prompt
‘Please enter your
option, one WAN Port ……’
.
Note
1. Add
‘#’
to the end of the password and select the new WAN
port connection type.
2. If you want to quit, press
‘*’
.
2
1) Pick up phone and press
‘****’
to start IVR.
2) Choose
‘2’
and the VIP-1000PT/T reports on the current
WAN Port IP
Address
.
3) Input the new WAN port IP address and end it with
‘#’
.
Use
‘*’
to replace
‘.’
. User can input
192*168*20*168
to set the
new IP address
192.168.20.168
.
Press the
‘#’
key to indicate that you have finished.
4) Report
‘operation successful’
if it’s done properly.
Note
1. If you want to quit, press
‘**’
.
2. Set the WAN IP and then Subnet Mask, Gateway and DNS
(Operation Code 3, 4 and 5); otherwise, new setting will be
invalid.
