background image

 

 

 

 

 

 

                      

 

©

2006 Pacific Cycle, Inc.

 

PROPER USE 

 

This swing set is designed for use by children ages 3 to 10 under adult supervision.  The maximum number of users this 
unit is intended for is 8 children with a maximum weight of 105 lbs each.  The maximum fall height for this swing set is 
74”. 
Single Ride (i.e. Swing)    

105 lbs 

Double Ride (i.e. Glider)  

210 lbs 

 
This product is designed for normal residential use only.  This product is not designed for use in day care, nurseries, or 
other public places.  This product is to be assembled by adults only in the manner described within this owner’s manual.  
The swing set must be anchored.  Anchors are not included in this carton.  For more information on anchoring, please see 
the section below.   

 
 

ANCHORING 

 

ANCHORING is necessary to prevent tipping, lifting, and overturning.  Playsafe™ recommends anchoring the swing set 
in concrete, especially in soft or sandy soil.  When this is not possible, anchors can be purchased by calling 1-800-242-6110. 
 
To anchor the swing set in concrete, dig a hole at least 5” deep and 10” to 12” in diameter.  Place the swing set leg in the 
hole, preferably on a brick or stone to keep if from sinking.   Be sure the swing leg is set 3” below the ground.  Also make 
sure the swing set is level.  Pour concrete around the legs and fill the hole.  Cover concrete adequately using the 
recommended surfacing instruction in this manual.  Allow the concrete to cure according to the concrete manufacturer’s 
instruction before use.  

 

 
 

CONSUMER INFORMATION FOR PLAYGROUND SURFACING MATERIALS 

 
The U.S. Consumer Product Safety Commission estimates that 100,000 playground related injuries are treated annually in U.S. 
hospital emergency rooms.  Injuries involving this hazard pattern tend to be among the most serious of all playground injuries, 
and have the potential to be fatal, particularly when the injury is to the head.  The surface under and around the playground 
equipment can be a major factor in determining the injury-causing potential of a fall.  It is self-evident that a fall on a shock-
absorbing surface is less likely to cause a serious injury than a fall onto a hard surface.  Playground equipment should never be 
placed on a hard surface such as concrete or asphalt and while grass may appear to be acceptable it may quickly turn to hard, 
packed earth in areas of high traffic.  Shredded bark mulch, wood chips, fine sand or fine gravel are considered to be acceptable 
shock absorbing surfaces when installed and maintained at a sufficient depth under and around playground equipment.   
 
The following table lists the maximum height from which a child would not be expected to sustain a life-threatening injury in a 
fall onto four different loose-fill surfacing materials if they are installed and maintained at depths of 6, 9, and 12 in.  However, all 
injuries due to a fall can not be prevented no matter what surfacing materials are used. 
 

FALL HEIGHT IN FEET FROM WHICH A LIFE 

THREATENING INJULY WOULD NOT BE EXPECTED 

Material Type 

 

6 in. depth 

9 in. 

12 in. 

Double Shredded 
Bark 

Mulch 

  6’ 

 10’ 

11’ 

Wood 

Chips 

  6’ 

 7’ 

12’ 

Fine Sand 

 

              5’ 

 

5’ 

 9’ 

Fine 

Gravel 

  6’ 

 7’ 

10’ 

 
It is recommended that a shock absorbing material should extend a minimum of 6’ in all directions from the perimeter of the 
stationary equipment such as climbers and slides.  However, because children may deliberately jump from a moving swing, the 
shock absorbing material should extend in front and rear of the swing a minimum distance of 2 times the height of the pivot point 
measured from a point directly beneath the pivot on the supporting structure. 
 
The information is intended to assist in comparing the relative shock-absorbing properties of various materials.  No particular 
method is recommended over another.  However, every material is only effective when properly maintained.  Materials should be 

Summary of Contents for Bristol 22-PS150













Reviews: