background image

YMER 3

OPERATORS GUIDE

March 2020

www.plcelectronicsolutions.com

D E S I G N E D   A N D   M A D E   I N   S W E D E N   S I N C E   1 9 6 4

®

D E S I G N E D   A N D   M A D E   I N   S W E D E N   S I N C E   1 9 6 4

®

YMER 3

 

OPERATORS GUIDE

The Ymer-3 has been developed as a cooperation between Hedén Group AB in Sweden 

and PLC Electronics Solutions in Canada. The system is built around the same basic idea 

as our legendary motors. User-friendly and robust have been our mindset throughout the 

development. Functions like lens mapping, LenSaver

TM

 manual calibration, manual override, 

for safe use on any lens with or without end stops and the quickest manual calibration system 

on the market.

Features include:

• 

Lens maping with pre marked scale rings for focus

• 

LenSaver

TM

 (patent pending) manual calibration

• 

Automatic calibration

• 

3 channel Receiver    

 

• 

Remote trigger

• 

Robust radio with a line of sight range of up to 500 m (1640 feet) 

• 

Industry-leading wireless control allowing for the fastest response of any long-range  

 

follow focus system on the market 

• 

Control knob with adjustable resistance for smooth individual operation

• 

Adjustable Zoom speed

• 

Lens limits and Macro functions at the press of a button

• 

5 threaded mounting points for attachments, two 1/4 inch, one 3/8 inch and two M4

• 

Transmitter powered by standard Sony NP-FM500H compatible battery

Summary of Contents for HEDEN YMER 3













Reviews: