background image

IP-010 

 

Page 

1

 of 

13

 

Revision 3 

 
 
 

The Pipe Line Development Company 

11792 Alameda Drive  •  Strongsville, Ohio  44149 

Phone: (440) 871-5700  •  Fax: (440) 871-9577 

Toll Free: 1-800-848-3333 

web: www.plidco.com  •  e-mail: pipeline@plidco.com 

 

PLIDCO

®

 CLAMP+SLEEVE 

INSTALLATION INSTRUCTIONS 

 

!! 

WARNING

!! 

IMPROPER SELECTION OR USE OF THIS PRODUCT CAN RESULT IN 
EXPLOSION, FIRE, DEATH, PERSONAL INJURY, PROPERTY DAMAGE 
AND/OR HARM TO THE ENVIRONMENT. 

 
Do not use or select a PLIDCO Clamp+Sleeve until all aspects of the application are thoroughly analyzed.  
Do not use the PLIDCO Clamp+Sleeve until you read and understand these installation instructions.  If 
you have any questions, or encounter any difficulties using this product, please contact PLIDCO. 
 

READ CAREFULLY 

The person in charge of the repair must be familiar with these instructions and communicate them to all 
personnel involved in the repair crew. 

Safety Check List 

Pipeline repairs can be made with the pipeline in operation or shutdown.

 

 

     

Read and follow these instructions carefully.  Follow your company’s safety policy and applicable 

codes and standards.  If the PLIDCO Clamp+Sleeve is to be installed underwater, be sure to read 
the 

Underwater Installation 

section. 

 

 

Whenever a PLIDCO product is modified in any form including adding a vent or changing seals 
by anyone other than the Engineering and Manufacturing Departments of The Pipe Line 
Development Company or a PLIDCO certified repacking company, the product warranty is voided.  
Products that are field modified do not have the benefit of the material traceability, procedural 
documentation, quality inspection and experienced workmanship that are employed by The Pipe 
Line Development Company. 

 

Clamp+Sleeves are designed to fit size-on-size.  Verification of the pipe outside diameter 
should be performed prior to installing a PLIDCO Clamp+Sleeve.  The fitting may have 
difficulty properly fitting onto oversized piping and may have difficulty properly gripping 
undersized pipe. 

 

 

A PLIDCO Clamp+Sleeve may be used as a structural clamp to couple pipe ends.  Verify the end 
restraint is sufficient to resist hydrostatic and, if applicable, dynamic and external forces such as 
thermal induced forces. 

 

 

Observe the Maximum Allowable Operating Pressure (MAOP) and temperature on the label of the 
PLIDCO product.  Do not exceed the MAOP or temperature as indicated on the unit. 

Summary of Contents for CLAMP+SLEEVE
















Reviews: