Introduction
Plockmatic PowerSquare™ 160 - Service Training Workbook
5
Figure 3. Extract from PDEC. Fig.11 - active tamper gate
• Every exploded diagram is followed by the related part number information. The
part number information is given for the top level assembly, sub-assemblies and
components where available. See
Figure 4. Extract from PDEC. Fig.11. Part number information.
A
Exploded diagram
A
Top-level assembly
B
Sub assembly
C
Component level
-XO
3
'
(
&
)
,*
$&
7
,9(
7
$0
3
(
5
*
$7
(
F
D
E
G
D
G
F
E
A
: 28
Part No.
Item
Description
Qty.
Fig.
FIG.11 - ACTIVE TAMPER GATE ASSEM BLY PSQ160 DE CK -PDEC
LAST EDIT:30 NOV 17
Fig11
894-638
P.ASSY, (PDEC) ACTIVE TAMPER GATE
1
1
894-639
• P.ASSY, (PDEC) TA MPER PIVOT DRIVE SIDE
1
1a
100-334
• • SCREW, SKT HD CAP, M2.5x10mm STAINLESS
1
1b
160-202
• • WASHER, M2.5 FORM A STAIN LESS
1
1c
258-223
• • ST STEEL, (PDEC) PIVOT LOCATION PLATE
1
1d
266-088
• • SHAFT,(PSQ) ACTIVE-GATE PIVOT PIN
1
•
2
100-406
• SCREW, SKT HD CAP, M3x8 HT ZP
4
3
160-002
• WASHER, M3 FORM A BZP
12
4
150-033
• NUT, M3 NYLOC-TYPE T
BZP
6
5
315-775
• PLASTIC,(PSQ) ACTIVE-GATE PIVOT BLOCK
1
6
894-640
• P.ASSY, (PDEC) TA MPER PIVOT PLATE
1
6a
266-088
• • SHAFT,(PSQ) ACTIVE-GATE PIVOT PIN
1
6b
258-223
• • ST STEEL, (PDEC) PIVOT LOCATION PLATE
1
6c
160-202
• • WASHER, M2.5 FORM A STAIN LESS
1
6d
100-334
• • SCREW, SKT HD CAP, M2.5x10mm STAINLESS
1
•
7
150-035
• NUT, M5 NYLOC-TYPE P
BZP
2
8
160-003
• WASHER, M5 FORM A BZP
4
9
281-927
• STEEL, (PDEC) PCB MOUNTING BRACKET
1
10
900-258
• PCB ASSEMBLY, S TEPPER MTR INTERCONNECT
1
11
742-806
• CABLE ASSEMBLY , (PSTO) TRIM SENSOR
1
12
710-016
• ELEC-HARDWARE, CABLE TIE-small
7
13
160-001
• WASHER, M4 FORM A
BZP
4
14
100-338
• SCREW, SKT HD CAP, M4 x 12mm STAINLESS
2
15
281-915
• STEEL, (PDEC) TAMPER MOTOR BRACKET
1
16
192-753
• GEAR, (PSTO) TAMPER DRIVE 28T 1MOD
1
A
B
C
Summary of Contents for Morgana PowerSquare 160
Page 72: ...Glossary of booklet making terms 68 Plockmatic PowerSquare 160 Service Training Workbook...
Page 73: ......
Page 74: ......
Page 75: ......