PLP Bushranger Edger Owner'S Manual Download

Page: 13 / 16

ASSEMBLY

• Tighten blade nut:

- Lower edger until blade

touches ground as shown.

- Hold opposite end of blade

spindle with wrench.

- Tighten nut to 39 N-m

(4.0kg-m).

Add Engine Oil

Do not check or add oil

when engine is running

Edger is shipped without

oil in engine. Add oil

before operating edger.

A. Dipstick

• Put edger on a level surface and

clean area around dipstick .

• Adjust cutting depth lever so

engine is level.

• Remove dipstick and add

approximately 0.41 L oil.

• Install and tighten dipstick.

Fill Fuel Tank

Do not mix oil with

gasoline. Use a clean fuel

container.

• Remove fuel tank cap.

• Fill tank with clean fresh

unleaded regular grade gasoline.

A. Fuel Tank Cap

Blade is sharp and can

cut you. Help avoid

injury before you tighten

blade nut:

Stop engine. Let engine

cool.

Wear gloves or wrap

blade with rag.

WARNING

A. Blade Nut

WARNING

CAUTION

Summary of Contents for Bushranger Edger

















Search results

Summary of Contents for Bushranger Edger

Reviews:

Related manuals for Bushranger Edger

Brands by name

Popular brands

PLP Bushranger Edger, Owner'S Manual

Search results

Summary of Contents for Bushranger Edger

Reviews:

Related manuals for Bushranger Edger

Brands by name

Popular brands