background image

Before you Start

Please read these instructions fully before starting. Although these instructions 

are comprehensive we always recommend that a technically competent installer 

undertake the installation.
Unpack and check that the shower tray is the colour, size, shape and type you require. 

Allow the shower tray to rest on a flat surface in a warm room then check for any 

damage. Do not install if not satisfied and contact your local supplier.
Check that the top surface of the shower tray is compatible with your intended shower 

enclosure, taking into account the loss of dimension that will result if the tray has been 

cut or trimmed to fit the available area and after tiles etc have been fitted.
The compatibility of the top surface of the tray and an enclosure is especially important 

if using a shower tray with a built in tiling upstand.
If you install this shower tray in conjunction with a steam unit, you must ensure the steam 

outlet is at a minimum of 350mm from the top of the tray.
When considering your installation method, you should be able to attach or repair 

your waste or waste outlet in-situ. 

Important

When handling your shower tray take care not to damage the bottom edges and 

when installing take particular care to protect the visible surfaces from impact 

damage or abrasions. 

Safety Notes

Caution: Care must be taken when drilling into walls or floors to avoid hidden pipes 

or electrical cables.
This product is heavy and requires a 2-person lift.

Care & Use of Your Shower Tray

These installation instructions should be retained and passed to the user for 

possible future reference.
It is normal for small amounts of localized water to be retained on the shower tray 

surfaces after use which should be wiped dry immediately to prevent build up of 

sediments.
The shower tray should be cleaned regularly with warm, soapy water only and dried with 

a cloth. Never use scourers, abrasives, bleach or other chemical cleaners.

Technical Help

Customer Service Line: 01386 800750

Dimensions are nominal and shown in millimetres unless otherwise stated.

Qty 1

Shower Tray  (Shape and style of tray may differ from that illustrated)

Summary of Contents for Shower Tray


















Reviews: