0000100437/010812/0 TEV-RANGE
EN - 7
waRNiNg!
Always switch
off
the machine and disconnect it
from the mains before carrying out the activities
below. First read the maintenance regulations at the
beginning of this manual.
Symptom
problem
possible cause
Solution
Motor does
not start.
Machine does
not function.
No mains
voltage.
Check the mains
voltage.
Mains cord
defective.
Repair or replace
mains cord.
Loose contacts.
Repair the
contacts.
Motor protection
switch defective.
Replace the
motor protection
switch.
Motor defective.
Repair or replace
motor.
Motor makes
a humming
sound, but
does not run.
Machine does
not function.
Motor uses 2
phases instead of
3 (three-phase
motor only).
Repair the phase
connection.
Motor capacitor
defective/not
connected (single
phase motor
only).
Repair or replace
the motor
capacitor.
Motor stops
automatically.
Machine does
not function.
Motor protection
switch activated.
Let the machine
cool down for
some time.
Check setting of
motor protection
switch (MPS)
according to
electrical
diagram.
Motor defective.
Repair or replace
the motor.
Poor suction.
Machine does
not function
properly.
Inverted
direction of
rotation of the
motor (three-
phase motor
only).
Change the
direction of
rotation.
Motor defective.
Repair or replace
the motor.
Extraction fan
polluted.
Clean the
extraction fan.
Outside air is
being extracted.
Check or replace
the sealing
material.
Vibrations in
the machine.
Machine not
steady.
Imbalance in the
extraction fan.
Clean the
extraction fan.
8
SpaRE paRTS
The following spare parts are available for the product (refer to
the exploded view,
article number
Description
TEV-385
0000100600
Fan wheel
TEV-385
0000100604
Motor TEV-385
; 230-400V/3ph/50Hz
TEV-585
0000100601
Fan wheel
TEV-585
0000100605
Motor TEV-585
; 230-400V/3ph/50Hz
article number
Description
TEV-765
0000100602
Fan wheel
TEV-765
0000100606
Motor TEV-765
; 230-400V/3ph/50Hz
TEV-985
0000100603
Fan wheel
TEV-985
0000100607
Motor TEV-985
; 230-400V/3ph/50Hz
9
ELEcTRicaL DiagRaM
Refer to the separately supplied electrical diagram.
10
DiSpOSaL
After life of the product, dispose it of in accordance with
federal, state or local regulations.
cE DEcLaRaTiON
CE declaration of conformity for machinery
We, Plymovent Manufacturing BV, Wezelkoog 11, 1822 BL
Alkmaar, the Netherlands, herewith declare, on our own
responsibility, that the product(s):
- TEV-385
- TEV-585
- TEV-765
- TEV-985
which this declaration refers to, are in accordance with the
conditions of the following Directive:
-
Machine Directive 2006/42 EC
- EMC directive 2004/108 EC
-
LVD 2006/95/EC
- ErP directive 2009/125/EC
Alkmaar, the Netherlands, 1 December 2012
Ir. F. Coehoorn
Vice President Research & Development
An installation is defined as a combination of several finished
products or components that are assembled by an installer at
a given place. The various parts of the installation are intended
to operate together in a particular environment and to perform
a specific task. The entire installation must comply with the
relevant directives and standards. The assembly instructions
given by the manufacturer, as well as the whole method of
installation, must be in accordance with good engineering
practices within the context of installations, as well as
installation rules. Considering the above, the installer will be
responsible for completing the installation and issuing the final
CE Declaration of Conformity.
