background image

Standard accessories:

Operating notes

Devices with ‘Interface’ option: bus connector

for fitting into top-hat rail

PMA

Prozeß- und Maschinen- Automation GmbH

P.O. Box 31 02 29

D-34058 Kassel

Tel.: +49 - 561- 505 1307

Fax: +49 - 561- 505 1710

E-mail: mailbox@pma-online.de

Internet: http://www.pma-online.de

Your local representative

Printed in Germany – Issue 10/2005 – Subject to changes without notice – 9498 737 48513

K S 4 5 1

0

Universal controller KS 45

0

1

without plug-in connector terminals

2

18...30VAC/18...31VDC, mA/V/

,

(0...20mA)

logic + 2 relays

INP2 as current input

3

90..260V AC, 2 optocoupler outputs,1 relay,

INP2 as current input (0...20mA DC and

0...50 mA AC)

4

18...30VAC/18..31VDC, 2 optocoupler outputs.,

1 relay, INP2 as current input

(0...20mA DC and 0...50 mA AC)

5

0
1

Standard configuration

0

Customer-specific configuration

9

Standard (CE-certification)

0

0

RS 485 / MODBUS - protocol

with screw terminal connector

90...260V AC, mA/V/logic + 2 relays,

(0...20mA)

INP2 as current input

1 universal input, 1 digital input
with display and BluePort interface

®

without options

0

90...260V AC, 2 output relays,

INP2 as current input (0...20mA)

18...30VAC/18...31VDC, 2

,

(0...20mA)

output relays

INP2 as current input

0

1

di1 as contact input

di1 as optocoupler input

1

INP2 as universal input, 0 -measurement,

di1 as contact input

2

INP2

,

di1 as optocoupler input

as universal input, 0 -measurement

2

2*

3*

* not on versions with optocoupler outputs (KS45-1x4... and KS45-1x5...)

00

2

System interface (only for 24V versions)

DIN 3440 / EN 14597

Ul/cUL certified

D

U

ORDERING DATA

Description

Order no.

Operating instructions for KS 45 (D)

9499-040-71818

Operating instructions for KS 45 (E)

9499-040-71811

Interface description for

Modbus rail line (D)

9499-040-72018

Interface description for

Modbus rail line (E)

9499-040-72011

Interface description for

PROFIBUS-DP (D)

9499-040-77118

Interface description for

PROFIBUS-DP (E)

9499-040-77111

Ø

Please also order the associated

documentation

(as separate item):

RL40-112-00000-000

Fieldbus coupler PROFIBUS DP
Fieldbus coupler PROFIBUS DP,

UL / cUL certified

RL40-112-00000-U00

Power supply module

UL / cUL certified

RL40-119-00000-000
RL40-119-00000-U00

Power supply module

SYSTEM COMPONENTS

Summary of Contents for KS 45









Reviews: