01-999-2521
Page 2
INTRODUCTION
Your Patio Pal evaporative air cooler was thoroughly tested and
inspected before leaving the factory. This manual is your guide
to economical, trouble free comfort cooling over the years with
reasonable care and regular maintenance. Failure to follow these
instructions may damage your cooler, impair its operation, and/or
void the warranty.
Read it carefully.
PREPARATION
Unpacking the unit
Remove the pad frame by lifting up and pulling outwards. The float
kit bag is located in the cooler bottom pan. Remove the float kit
bag from the cabinet. Float kit contains the following items:
1. Float valve assembly
2. Float bracket
3. Garden hose adapter
4. Overflow stand pipe
5. Drain Bushing Assembly
SET UP FOR USE
Install float valve and hose adapter. Attach the float valve to the
cabinet as shown in figure 3. The garden hose adapter attaches to
the brass inlet fitting on the float valve
(See figure 3)
.
NOTE:
Verify
that the hose washers are correctly in place before use.
Next install the overflow stand pipe and drain bushing. Attach the
stand pipe, drain bushing, and washer in the hole in the drain pan
in the order shown in
figure 4
.
NOTE:
Verify that the washer is
correctly in place before use.
Water connection and float adjustment
Move cooler to desired location (must be a level area for proper
operation of the cooler).
1. Connect water supply using a commercial grade water hose (not
supplied with cooler, obtained separately) to the adapter on the
float valve and turn water on.
CAUTION:
water inlet pressure
should be limited to a maximum of 65 PSI to avoid rupturing the
water hose. If pressure exceeds this valve, an inline pressure
regulator should be installed (obtainable from a local plumbing or
hardware store).
2. Check that all connections are tight by visually inspecting hose,
float valve, etc. for leakage.
3. Set float valve for a water depth of 2.5". The float is adjusted by
lightly bending the float rod.
4. Do not insert garden hose into manual fill door; water may harm
the pump and void the warranty.
Figure 1
Figure 2
Figure 3
01-999-2521
Page 7
PP5000 - Replacement Parts List
Item
Replacement Part
Part Number
1
Switch Box Cover
05-004-0003
2
Pad Frame Assembly
05-001-0145
3
3" Celdek Media (Set of 2)
05-002-0193
4
Water Distributor Assembly
05-006-0193
5
Switch Box
05-007-0062
6
120V Motor Receptical
05-007-0061
7
120V Pump Receptical
05-007-0060
8
Blower Pulley
05-003-0059
9
Belt
05-003-0219
10
Pump - 120V
05-006-0221
11
Overflow Standpipe Kit
05-006-0005
12
Float Valve Assembly
05-006-0001
13
Bearing Assembly (Set of 2)
05-003-0037
14
Blower Wheel
05-003-0034
15
Shaft
05-003-0001
16
Delrin Spacers (Pair)
05-003-0082
17
Motor 1/2 Hp, 120V
05-007-0042
18
Grille Handle Sleeve (Set of 2)
05-001-0146
19
Drain Plug
05-001-0147
20
Gas Springs (Set of 2)
05-001-0148
21
Cutting Boards (Set of 2)
05-001-0149
22
Float Bracket
05-006-0186
23
Garden Hose Adapter
05-006-0242
1
3
2
18
21
9
17
19
10
20
4
7
6
5
13
14
15
16
8
BLOWER ASSEMBLY
11
23
12
22
Item
Replacement Part
Part Number
1
Switch Box Cover
05-004-0003
2
Louver Panel Assembly
05-001-0145
3
3" Celdek Media (Set of 2)
05-002-0193
4
Water Distributor Assembly
05-006-0193
5
Switch Box
05-007-0062
6
120V Motor Receptical
05-007-0061
7
120V Pump Receptical
05-007-0060
8
Blower Pulley
05-003-0059
9
Belt
05-003-0219
10
Pump - 120V
05-006-0221
11
Overflow Standpipe Kit
05-006-0005
12
Float Valve Assembly
05-006-0001
13
Bearing Assembly (Set of 2)
05-003-0037
14
Blower Wheel
05-003-0034
15
Shaft
05-003-0001
16
Delrin Spacers (Pair)
05-003-0082
17
Motor 1/2 Hp, 120V
05-007-0042
18
Grille Handle Sleeve (Set of 2)
05-001-0146
19
Drain Plug
05-001-0147
20
Gas Springs (Set of 2)
05-001-0148
21
Cutting Boards (Set of 2)
05-001-0149
22
Float Bracket
05-006-0186
23
Garden Hose Adapter
05-006-0242
PP5000 - Replacement Parts List
01-999-2519 Date: 2/27/2015
