Instructions > PMI Ventilator
REMOVAL FROM SERVICE
The PMI Ventilator provides the protection you need working in
a vertical rope world. It features a Kevlar shell giving your head
maximum protection. It meets ANSI Z89.1, Type 1 Fully adjustable
three point chinstrap and ratchet system provide a perfect fi t.
Weight:
1.13 lbs (513 g)
If any of the following occur, this helmet must be removed from service
and destroyed:
• If the helmet received a signifi cant impact.
• If the helmet shows cracks that are more than superfi cial.
• If any part of this helmet shows signifi cant damage or excessive wear.
• If the helmet is has been visibly damaged by heat, chemicals, etc.
• If this helmet has been in service for 5 years, regardless of condition.
• If this helmet cannot be properly adjusted.
INSPECTION
MAINTENANCE AND CARE
Inspect the helmet for obvious damage. Check the shell for cracks
and dents. Minor surface cracks will not impair the effectiveness of
this helmet. Check the webbing and buckles for damage or excessive
wear.
This helmet should be assigned to a single user who is responsible for
inspecting it after each use. Make sure that the surface of the helmet
has no dents or signifi cant cracks. Inspect the webbing and buckles
for damage or excessive wear. If needed, wash the helmet with clear
water or a mild soap, such as PMI Rope Soap. Ordinary laundry
detergent, or solutions that may contain bleach, should not be used on
life safety gear.
Air dry in a cool, dry place out of direct sunlight. Store the helmet in
a cool place where it will be protected from exposure to potentially
damaging chemicals. Repair or modifi cation of this product without
the manufacturers written consent is strictly forbidden. You should
establish a record of the inspections of this equipment. You may need
to develop your own inspection log format depending on your needs.
HELMET TECH INFO
A comfortable, well-fi tting helmet that is designed specifi cally for
vertical work is essential. Helmets must have a secure chin strap and
a three-point suspension to keep the helmet on the head when it is
needed most. A three point suspension refers to a helmet with webbing
support points on both sides of the helmet and one at the rear. The
chin strap should also be designed so that a relatively high force is
required to cause a release. This helps keep the helmet on the user’s
head in a tumbling fall. The inside suspension of the helmet should hold
the shell away from the skull during a blow to the helmet and should
provide air circulation and comfort, particularly during hot weather.
The shell should have the rigidity to resist impact to the helmet and
penetration by sharp objects but be fl exible enough to absorb some
of the blow that otherwise would be directly transmitted to the skull
and spine.
The design of the helmet should protect the head against objects
falling from above and hitting from the side. A slight brim helps
prevent rainwater or spray from dripping into your face. However,
your helmet should have a narrow enough profi le to allow you a good
upward fi eld of vision and to ensure that the back of the helmet does
not catch on a backpack when you raise your head.
This helmet is not designed to provide protection from the following hazards:
non-ionizing radiation, ionizing radiation, external radiation or any condition
not expressly stated in this use information.
CERTIFIED
ANSI Z89.1, Type 1
WEBV1-0411
PMI LIMITED WARRANTY
PMI products are warranted to the original retail purchaser to be free from defect in material and workmanship for a period of one year. PMI will repair or replace the item without charge provided
inspection at our factory discloses no misuse or alteration, which, in our judgment, has affected the condition or functioning of the product. All implied warranties imposed by law in connection with the sale
of PMI products are also limited in duration to a period of one year. PMI expressly excludes and shall not be liable for any consequential damages arising out of any breach of the express or implied
warranties on sales of PMI products. Because of the high risks involved in high angle rope work such as, but not limited to, rescue, rope access, caving, rappelling, rock climbing and mountaineering, no further
warranties exist or are implied by PMI. Regulations issued under the Magnuson-Moss Warranty Act require us to include the following statement: some states do not allow limitations on how long an implied
warranty lasts nor the excluding or limitation of incidental or consequential damages, so the above limitations may not apply to you.
WARNING
CAUTION
Use this PMI Helmet only if you have been properly trained by an instructor
who is well qualifi ed in all phases of vertical rope work. Good instruction
includes evaluation of the students comprehension of and ability to safely
and effi ciently perform the task(s) being taught.
