Cable
management
gully
pmv
mounts
.co.uk
Assembly instructions for dual screen kits
PMVTROLLEYXLDS1
&
PMVTROLLEYXLDS2
on to
PMVTROLLEYXL
or
PMVSTAND
.
PMVTROLLEYXLDS1
- x2 40" - 55" up to 30Kg per screen.
Designed & Manufactured
in the United Kingdom
Read these instructions carefully before assembling this equipment.
Assemble in a suitable location.
Check the equipment has been supplied with all parts and fixtures prior to assembly.
Three people will be required for assembly and for installation of the screens on to the equipment.
Do not attempt to alter or modify any part of the equipment or its attachments.
Do not use if any parts are broken or appear to be damaged.
Only use fixings provided with this bracket.
Tighten all bolts and fixings securely with appropriately sized tools.
Do not position the equipment close to sources of heat or moisture.
PMVTROLLEYXLDS2
- x2 27" - 46" up to 30Kg per screen in landscape.
- x2 47" - 55" up to 30Kg per screen in portrait
PMVTROLLEYXL
PMVSTAND
NOTE:
PMVTROLLEYXLDS1
&
PMVTROLLEYXLDS2
are not standalone products, they
should knowingly be sold and used as an accessory(s) for PMVTROLLEYXL or
PMVSTAND only.
PMVTROLLEYXL
should be built in full prior to installation of the TV bracket as per
its instructions. The x4 lower trim inserts can be installed but it may be beneficial to
install the x2 upper trim inserts after the trolley and dual screen accessory are fully
installed and cabling can be tidied.
PMVSTAND
should be built in full as per its included instructions. The x4 lower trim
inserts can be installed but it may be beneficial to install the x2 upper trim inserts
after the trolley and dual screen accessory are fully installed and cabling can be
tidied.
If your trolley or stand are assembled with castors, ensure the brakes are applied until
installation of screens and they are bolted in to their final position.
Assembly fixing kit checklist
Component checklist
D
- M8 x 16mm
E
- M8 nut
C
- M8 nut cover
B
- M8 x 12mm
A
- M8 washer
X40
X28
X4
X3
X12
Screen fixing kit checklist
F
- M4 x 20mm
I
- M8 x 20mm
H
- M6 x 20mm
G
- M5 x 20mm
L
- M8 washer
K
- M6 washer
J
- M5 washer
M
- M4 x 5mm
P
- M6 x 6mm
O
- M6 x 6mm
N
- M5 x 5mm
X8
X8
X8
Trim Inserts:
You may find it easier to insert one of each 600mm trim inserts in to each of the
extrusions before installing the dual screen kit on to the trolley.
For PMVTROLLEYXLDS1 you will need to cut your third trim insert at its mid length
with sharp scissors or a safety knife or as your needs require.
Inserts can be installed by sliding them down the formed grooves of the extrusion or
placed in one groove and popped in to the opposing groove.
The trim pieces can be cut with a safety knife after installation to make small entry
and exit points for cables.
Trim inserts are made from a plastic board material and like any paper or cardboard
product can be sharp. Do not pull or tug your cables against edges of the board as
this may damage the protective sheath of the cable.
Inside face of extrusion
Trim insert
Outside face of extrusion
Slider gully
Top down view
Trim insert
Isometric
view
Tilting VESA plate
x2
Screen mount hanger
x2
TV mounting plate
sliders
x4
Single stud
slider
x4
600mm trim inserts
x3 (DS1) x2 (DS1)
Vertical TV mounting arms
x4
Horizontal TV mounting arms
x4
Support brace
x1
Top supports
x2
Open sliders
x4
900mm aluminium extrusion assembled with joining plate
x2 (PMVTROLLEYXLDS1)
600mm extrusion with joining plate
x2 (PMVTROLLEYXLDS2)
Extrusion trim pieces
x2
