background image

4  

 

SAFETY 

IMPORTANT SAFETY INSTRUCTIONS FOR USING STAPLERS 

DANGER 

1. OPERATORS AND OTHERS IN WORK AREA MUST WEAR SAFETY GLASSES WITH SIDE SHIELDS. 

• 

Never use oxygen, combustible gases or any other bottled gases as a power source for the Sta-
pler. 

• 

Use of the above gases is dangerous, as the Stapler will explode. 

• 

Use only clean, dry, regulated compressed air. 

• 

When operating the Stapler, always wear eye safety glasses with side shields, and make sure 
others in the work area wear safety glasses, too. 

• 

Safety glasses must conform to the requirements of American National Standards Institute, 
ANSI Z87.1 and provide protection against flying particles both from the front and side. 

• 

The employer must enforce the use of safety glasses by the Stapler operator and others in work 
area. 

WARNING 

3. NEVER POINT TOOL AT YOURSELF OR OTHERS IN WORK AREA. 

• 

Always assume the Stapler contains fasteners. 

• 

Never point the Stapler at yourself, toward yourself or others whether it contains fasteners or 
not. 

• 

If fasteners are mistakenly driven, it can lead to severe injuries. 

• 

Never engage in horseplay with the Stapler. 

• 

Respect the Stapler as a working implement. 

4. KEEP FINGERS AWAY FROM TRIGGER WHEN NOT DRIVING STAPLES TO AVOID ACCIDENTAL FIRING. 

• 

Never carry the Stapler with finger on trigger since you could drive a fastener unintentionally and injure yourself or 
someone else. 

• 

Always carry the Stapler by the handle only. 

5. CHOICE OF TRIGGERING METHOD IS IMPORTANT. 

• 

Read and understand section titled “METHODS OF OPERATION.” (page 12) 

6. DO NOT EXCEED 120 psi. (6.9 bar 8.4 kgf/cm2) 

7. ALWAYS WEAR EAR AND HEAD PROTECTION. 

• 

Always wear ear protection to protect your ears from loud noise. 

• 

Always wear head protection conforming to ANSI Z89.1-1986 protect your head from flying objects. 

2. NEVER USE OXYGEN OR OTHER BOTTLED GASES. EXPLOSION MAY OCCUR. 

READ ALL INSTRUCTIONS 

• 

Do not exceed maximum recommended air pressure 120 psi  
(6.9 bar 8.4 kgf/cm2) 

• 

Never connect the Stapler to pressure which potentially exceeds 200 
psi (13.7 bar 14 kgf/cm2) as the Stapler can burst. 

120psi 

120psi 

Summary of Contents for 461A





















Reviews: