background image

20 

 

4. Notes for battery disposal and battery replacement 

 

  The battery of standard unit is of valve regulated, maintenance free. It can attain expectant life only by 

keeping frequent charging. Regardless of UPS on or off when UPS connects to utility power, the battery is 

charged all the time and UPS offers protection for over-charge and over-discharge. 

  Normally the battery life is three to five years and the battery must be replaced ahead of time once there 

presents any abnormal status. The battery replacement must only be performed by qualified personnel. 

  It is inadvisable to replace a single battery. Operator should obey the instruction of battery distributor 

when replacing all batteries. 

  The batteries should be charged and discharged once every four to six months. After UPS discharged to 

off, the batteries should be recharged. The charge time of standard unit must be more than 12 hours. 

  The battery must be charged and discharged once every two months in high-temperature area. The 

charge time of standard units must be more than twelve hours. 

 

1.  If  it  is  necessary  to  replace  any  connection  cables,  please  purchase  the  original  materials  from  the 

authorized distributors or service centers, so as to avoid overheat or spark resulting in fire due to insufficient 

capacity. 

 

2. Do not dispose of batteries or battery packs in a fire, they may explode. 

 

3. Do not open or mutilate batteries, released electrolyte is highly poisonous and harmful to the skin and 

eyes. 

 

4. Do not short the positive and negative of the battery electrode, otherwise, it may result in electric shock 

or fire. 

 

5. Make sure that there is no voltage before touching the batteries. The battery circuit is not isolated from 

the input potential circuit. There may be hazardous voltage between the battery terminals and ground. 

 

6. Even though the input breaker is disconnected, the components inside the UPS are still connected with 

the  batteries,  and  there  are  potential  hazardous voltages.  Therefore,  before  any maintenance  and  repairs 

work is carried out, switch off the breaker of the battery pack or disconnect the jumper wire of connecting 

between the batteries. 

 

PDF 

文件使用

 "pdfFactory Pro" 

试用版本创建

 

www.fineprint.cn

Summary of Contents for H1KL
























Reviews: