Pocket NC V2-50DA Manual Download | Manualshive

Page: 7 / 16

background image

3) With the enclosure carefully overhanging a table or workbench as shown, start one of

the M4x6 fasteners into the screw hole closest to the USB port using a 3mm hex key.

4) Rotate the machine so the chip tray opening is hanging off the table and install one of

the M4x6 screws into the back of the machine.

7

«
...
5
6
7
8
9
...
»

Summary of Contents for V2-50DA

















Reviews:

No comments

Related manuals for V2-50DA

Brand: ABB Pages: 63

Brand: Keithley Pages: 97

Brand: Happ Pages: 52

Brand: Hansen Pages: 4

Brand: Samsung Pages: 16

Brand: Datavideo Pages: 17

Brand: Datamax Pages: 22

Brand: LAIA Pages: 71

Brand: IN-COMMAND Pages: 47

Brand: SYCLOPE Pages: 60

Brand: K&K Pages: 10

Universal Family for Sony

Brand: Jolly Pages: 68

DMC-40x0 Series

Brand: Galil Motion Control Pages: 280

Brand: L&L Pages: 16

Ratio Feeder J+ Advanced Series

Brand: H.E. Anderson Pages: 11

Brand: National Instruments Pages: 14

Brand: Sturtevant Richmont Pages: 73

Brand: Stramatel Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands