Polaris Light Utility Hauler 6x6 Owner'S Manual Download

Page: 115 / 116

113

INDEX

Accessories

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Adjustments

81-89

. . . . . . . . . . . . . . . . . . . . . . . . .

Age Restrictions

. . . . . . . . . . . . . . . . . . . . . . . . . .

Air Box Drain

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Air Filter

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

All Wheel Drive (AWD) System

42-43

. . . . . . . . . .

Auxiliary Brakes

. . . . . . . . . . . . . . . . . . . . . . . . .

Battery Fluid

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Battery Installation and Connections

. . . . . . . . .

Battery Maintenance

95-97

. . . . . . . . . . . . . . . . . . .

Battery Removal

. . . . . . . . . . . . . . . . . . . . . . . . .

Battery Storage

. . . . . . . . . . . . . . . . . . . . . . . . . .

Belt Life

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Brake, Front

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Brake, Parking

. . . . . . . . . . . . . . . . . . . . . . . . . .

Brake, Rear

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Brakes

35-36

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Breather Filter

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Camber and Caster

. . . . . . . . . . . . . . . . . . . . . . .

Carburetor Adjustment

. . . . . . . . . . . . . . . . . . . .

Carburetor Adjustments

. . . . . . . . . . . . . . . . . . .

Choke Adjustment

. . . . . . . . . . . . . . . . . . . . . . .

Cleaning and Storage

102-103

. . . . . . . . . . . . . . . .

CONTROLS

32-41

. . . . . . . . . . . . . . . . . . . . . . . . .

Cooling System Operation

. . . . . . . . . . . . . . . . .

Crossing Streams

. . . . . . . . . . . . . . . . . . . . . . . .

Disengaging Wheel Hubs

. . . . . . . . . . . . . . . . . .

Drive Chain Adjustment

85-86

. . . . . . . . . . . . . . . .

Driving in Reverse

59-60

. . . . . . . . . . . . . . . . . . . .

Driving on Slippery Surfaces

. . . . . . . . . . . . . . .

Driving Over Obstacles

. . . . . . . . . . . . . . . . . . . .

Driving Procedures

. . . . . . . . . . . . . . . . . . . . . . .

Driving Safely

50-62

. . . . . . . . . . . . . . . . . . . . . . .

Dumping Cargo

. . . . . . . . . . . . . . . . . . . . . . . . .

Engine Cooling System

77-78

. . . . . . . . . . . . . . . .

Engine Idle RPM Adjustment

. . . . . . . . . . . . . . .

Engine Specifications

105

. . . . . . . . . . . . . . . . . . . .

FEATURES

42-43

. . . . . . . . . . . . . . . . . . . . . . . . .

FEATURES AND CONTROLS I.D.

. . . . . . . . . .

Filter Systems

79- 80

. . . . . . . . . . . . . . . . . . . . . . . .

Front Gearcase Lubrication

. . . . . . . . . . . . . . . . .

Front Wheel and Middle Axle Brake

. . . . . . . . .

Front Wheel Hub Tightening

. . . . . . . . . . . . . . .

Fuel System

38-39

. . . . . . . . . . . . . . . . . . . . . . . . .

Gear Selector Operation

. . . . . . . . . . . . . . . . . . .

Gearcase Oil Changing

. . . . . . . . . . . . . . . . . . .

Handlebar Adjustment

. . . . . . . . . . . . . . . . . . . .

Hauling Cargo

48-49

. . . . . . . . . . . . . . . . . . . . . . . .

Headlight Adjustment

. . . . . . . . . . . . . . . . . . . . .

Headlight Housing Replacement

100

. . . . . . . . . . . .

Headlight Lamp Replacement

. . . . . . . . . . . . . . .

Horn Switch

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

IDENTIFICATION NUMBERS

. . . . . . . . . . . . . .

Indicator Lamp Replacement

101

. . . . . . . . . . . . . .

Jetting Chart

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Know Your Vehicle

. . . . . . . . . . . . . . . . . . . . . . . .

Light Switch

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Lights

98-101

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Load Distribution

. . . . . . . . . . . . . . . . . . . . . . . .

Lubrication Recommendations

68-75

. . . . . . . . . . .

Main Switch

32-33

. . . . . . . . . . . . . . . . . . . . . . . . .

MAINTENANCE AND LUBRICATION

64-103

. . .

Maintenance Record

. . . . . . . . . . . . . . . . . . . . . .

Making Turns

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Master Cylinders

. . . . . . . . . . . . . . . . . . . . . . . . .

NOISE CONTROL SYSTEM

. . . . . . . . . . . . . . .

Oil Change

74-75

. . . . . . . . . . . . . . . . . . . . . . . . . .

Oil Filter Change

74-75

. . . . . . . . . . . . . . . . . . . . .

Oil System

38-39, 73

. . . . . . . . . . . . . . . . . . . . . . . .

Operating Safety

. . . . . . . . . . . . . . . . . . . . . . . . .

OPERATION

44-62

. . . . . . . . . . . . . . . . . . . . . . . .

Operator Safety

5-30

. . . . . . . . . . . . . . . . . . . . . . . .

Override Switch

. . . . . . . . . . . . . . . . . . . . . . . . .

POLARIS RECOMMENDED PRODUCTS

106

. . . .

Parking On An Incline

. . . . . . . . . . . . . . . . . . . .

Periodic Maintenance Schedule

65-67

. . . . . . . . . .

Pre--Ride Inspection

. . . . . . . . . . . . . . . . . . . . . .

Premium 4 Synthetic Lubricant

. . . . . . . . . . . . .

PVT System

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Radiator Coolant Level

. . . . . . . . . . . . . . . . . . . .

Recoil Starter

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Recovery Bottle Coolant Level

. . . . . . . . . . . . . .

Reverse Speed Limiter

. . . . . . . . . . . . . . . . . . . .

Safe Riding Gear

. . . . . . . . . . . . . . . . . . . . . . . . .

SAFETY

5-30

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety Decals and Locations

10-13

. . . . . . . . . . . . .

Safety Training

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Service Brakes

. . . . . . . . . . . . . . . . . . . . . . . . . .

Setting the Parking Brake

. . . . . . . . . . . . . . . . . .

Side Panel Removal

. . . . . . . . . . . . . . . . . . . . . .

Sidehilling

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Spark Arrestor

63, 93, 95

. . . . . . . . . . . . . . . . . . . .

Spark Plug Removal

. . . . . . . . . . . . . . . . . . . . . .

Spark Plugs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SPECIFICATIONS

104-105

. . . . . . . . . . . . . . . . . .

Specifications

90-91

. . . . . . . . . . . . . . . . . . . . . . . .

Starting a Cold Engine

. . . . . . . . . . . . . . . . . . . .

Starting a Warm Engine

. . . . . . . . . . . . . . . . . . .

Steering Inspection

. . . . . . . . . . . . . . . . . . . . . . .

Stop Switch

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Suspension Springs

. . . . . . . . . . . . . . . . . . . . . . .

Switches and Indicators

32-33

. . . . . . . . . . . . . . . .

TABLE OF CONTENTS

. . . . . . . . . . . . . . . . . . .

Taillight/Brakelight Lamp Replacement

101

. . . . . .

Throttle Lever

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Tire Specifications

. . . . . . . . . . . . . . . . . . . . . . .

Tires

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Toe Alignment

. . . . . . . . . . . . . . . . . . . . . . . . . .

Tool Kit

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Torque Specifications

. . . . . . . . . . . . . . . . . . . . .

Towing Capacities

. . . . . . . . . . . . . . . . . . . . . . . .

Transmission Lubrication

. . . . . . . . . . . . . . . . . .

Transmission Oil Change

. . . . . . . . . . . . . . . . . .

Transporting the Vehicle

103

. . . . . . . . . . . . . . . . . .

Traveling Downhill

. . . . . . . . . . . . . . . . . . . . . . .

Traveling Uphill

. . . . . . . . . . . . . . . . . . . . . . . . .

TROUBLESHOOTING

108-109

. . . . . . . . . . . . . .

Turning Around on a Hill

. . . . . . . . . . . . . . . . . .

Vehicle Break--in

. . . . . . . . . . . . . . . . . . . . . . . .

Vehicle Specifications

104

. . . . . . . . . . . . . . . . . . . .

Vehicle Storage

103

. . . . . . . . . . . . . . . . . . . . . . . . .

WARNING, READ OWNER’S MANUAL

. . . . .

Warranty

110-111

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Washing the Vehicle

102

. . . . . . . . . . . . . . . . . . . . .

Waxing the Vehicle

102

. . . . . . . . . . . . . . . . . . . . . .

WELCOME

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Wheel Installation

. . . . . . . . . . . . . . . . . . . . . . . .

Wheel Removal

. . . . . . . . . . . . . . . . . . . . . . . . .

Wiring Diagram

107

. . . . . . . . . . . . . . . . . . . . . . . .

Summary of Contents for Light Utility Hauler 6x6





















































































































Search results

Summary of Contents for Light Utility Hauler 6x6

Reviews:

Related manuals for Light Utility Hauler 6x6

Brands by name

Popular brands

Polaris Light Utility Hauler 6x6, Owner'S Manual

Search results

Summary of Contents for Light Utility Hauler 6x6

Reviews:

Related manuals for Light Utility Hauler 6x6

Brands by name

Popular brands