background image

www.polarispool.com

Congratulations on the purchase of your new automatic pool cleaner, and thank you for
choosing Polaris. The Polaris 65/Turbo Turtle for aboveground pools and the Polaris
165/Super Turtle for in-ground vinyl or fiberglass pools are designed to give you years of
dependable and efficient service.

Like most mechanical devices, these cleaners will require periodic adjustments, routine
maintenance, and the replacement of certain hardworking parts. Please have your
cleaner checked occasionally by your local Polaris dealer or authorized service center.

Always insist on genuine Polaris replacement parts. Non-Polaris parts are not made to
our specifications. They may have an adverse effect on the operation of your Polaris or
may even damage it.

Introduction

9

8

7

10

6

1a

1b

2

5

4

3

1a.

Surface Module 

1b.

Turtle Top

0

2.

Wheel Cage

0

3.

Sweep Hose 

0

4.

Jet Sweep Assembly

0

5.

All-Purpose Bag

0

6.

Float Hose Extension with Connector

– 165 and Super Turtle only

0

7.

Float Hose 

0

8

Quick Disconnect

0

9.

Universal Wall Fitting (UWF)

10.

Eyeball Regulators (2) – 165 and 
Super Turtle only

English

Polaris Complete Cleaner

 

 

 

 

Summary of Contents for Polaris 165 SuperTurtle










Reviews: