8
Get OUT of Valet Mode
1. Turn on the Ignition Key.
2. Press and hold the Valet Push-Button for 2 seconds. The L.E.D. will turn OFF.
MULTI-SPEED TACH LEARNING
On some Ignition systems, the Tach signal can be too high or too low, causing failed starts under certain temperatures. The
PS-3085 SH system is designed to read a wide range of Tach signals. No manual adjustments are necessary. Each time a new
Unit is installed, however, new Tach adjustment procedures should be carried out.
The Tach learning procedure is as follows:
1. Ensure that Ignition is OFF
x
Hold the Hood Pin-Switch down for 4 seconds.
x
Release the Pin-Switch.
The Parking Lights should come ON.
x
With the Parking Lights ON, immediately push and release the Pin-Switch again.
The Parking Lights will stay
on for up to 20 seconds
.
2. Press and hold the Brake Pedal and press the LOCK + UNLOCK buttons simultaneously on the Transmitter
The
Parking Lights will flash 4 times.
3. Release the Brake Pedal and start the vehicle; allow it to reach regular Engine idle speed.
The Parking Lights will
go out when the Tach is detected.
4. Press and release the Brake Pedal: if the Parking Lights flash 5 times, the Tach signal has been learnt
.
To end Tach learning at any time, close the Hood.
NOTE:
The Horn will give 1, 2 or 3 signals to indicate which Tach mode was sensed. (The Horn signals will only be heard if
Aux. 2 is programmed for HORN – Mode 3, Function 3, Option 3.)
PROGRAMMING OPTIONS
The
PS-3085 SH
System is equipped with 3 custom programming menus that allow the user to custom-fit the outputs of the
system according to the installation requirements.
To get into custom programming mode you must do the following:
1. Make sure that Ignition is OFF.
x
Hold the Hood Pin-Switch down for 4 seconds.
x
Release the Pin-Switch.
The Parking Lights should come on.
x
With the Parking Lights on, immediately push and release the Pin-Switch again.
The Parking Lights will stay
on for up to 20 seconds
.
2. Press and hold the Brake Pedal, then press:
x
LOCK button for MODE 1
x
UNLOCK button for MODE 2
x
TRUNK button for MODE 3
NOTE:
Depending on the MODE you want to change, the Horn and the Parking Lights will give one signal for
Mode 1, two signals for Mode 2, and three for Mode 3. (The Horn signals will only be heard if Aux. 2 is
programmed for HORN – Mode 3, Function 3, Option 3.)
3. Release the Brake Pedal.
NOTE:
The Unit will stay in Programming Mode until the Hood Pin-Switch or Brake Pedal is pressed again.
(
Therefore,
take your time to make the proper selection.)
Each Mode has functions for which options must be selected. Once you have selected either Mode 1, Mode 2 or Mode 3, the
system automatically moves to function one. You must then select the desired option for each function. Once you have
selected an option, you will move to the next function, and so on.
To select one of the four options, press the appropriate button on the Transmitter (see below).
x
LOCK = option 1
x
UNLOCK = option 2
x
TRUNK = option 3
x
START = option 4
Once an option has been selected, the Parking Lights will flash 1, 2, 3 or 4 times depending on the option that has been
selected.
Take your time to make the proper selections. The Unit will stay in programming mode until the Hood Pin-Switch is pressed.
Pressing the Brake Pedal will bring you back to the programming menu, where you can select the next Mode.
Summary of Contents for PS-3085 SH
Page 6: ...6 WIRING DIAGRAM ...
