background image

P. 10

 User 

Guide

 

 

 
 
 
 

Troubleshooting Poor Transmitting Range 

Many factors may affect the operating range of the transmitter.  Some of these are: 

 

The condition of the battery in the transmitter. 

 

The operating environment (for example: downtown radio-frequency noise, airports, cellular 
phone towers…) 

 

Metal: any type of metal will affect operating range. This includes the metal in the car. 

 

The shape of the vehicle can affect range as well; vans in general have an especially poor 
range. 

 

The shape of the roof and A-pillars brings about considerable radio-frequency deflection (in 
this case the signal from the remote control). As a result, the direction in which the vehicle is 
facing in relation to the remote control can affect the range. Straight on – standing in front of 
the vehicle – generally gives you the greatest range; the second best performance is from the 
back. Using the remote control from either side of the vehicle will usually give the lowest 
range. 

 

The range will be significantly lower in a crowded parking lot than in open space. 

 

Always hold the transmitter high, approximately at shoulder height. Holding the transmitter 
against your chin will also increase your range: your head acts as an antenna.  

 

The operating range will be somewhat lower on vehicles equipped with an aftermarket or 
factory alarm. 

Summary of Contents for PS-3135













Reviews: