background image

PS-3185SH 

User Guide

  

P. 

 

Remote-Starting Your Vehicle 

Setting Your Vehicle into Ready Mode 

This product is designed for vehicles with a manual transmission only. In order to start the vehicle 
by remote, the unit must first be set to Ready Mode. If the unit is not set to Ready Mode, it cannot 
remote-start the vehicle. Once the system is set to Ready Mode, the vehicle can be remote-started 
and stopped at wish. The system will exit Ready Mode if a door or the hood is opened, if the brake 
pedal is pressed, if the parking brake is disengaged or if the ignition key is turned to the 

IGNITION ON 

(RUN)

 position. 

To set the system to Ready Mode: 
1.

 

Ensure that all the doors are closed and that the shifter is in the neutral position. 

2.

 

With the engine already running, apply the parking brake and release the brake pedal. 
Make sure to release the brake pedal. 

3.

 

Within 20 sec. press 

LOCK

UNLOCK

 or 

START

 on the transmitter. 

The parking lights will flash 3 times quickly and remain lit. 

4.

 

Remove the key: the engine will go on running. 

5.

 

Exit the vehicle and close the door. 

6.

 

Press and hold either: 
a.

 

LOCK

 to lock the doors and shut down the engine; 

b.

 

UNLOCK

 to unlock the doors and shut down the engine; 

c.

 

STOP

 to shut down the engine without affecting the doors. 

Remaining In Ready Mode 

Once the vehicle is in Ready Mode you can start and stop the vehicle at wish. However, should 
any of the following occur, the vehicle will exit Ready Mode – thus eliminating the remote start 
option until Ready Mode is restored: 

 

Door opened; 

 

Hood opened; 

 

Brake pedal pressed; 

 

Parking brake disengaged; 

 

Ignition key turned to the 

IGNITION ON (RUN)

 position. 

Should any of the above occur, Ready Mode will be cancelled. 

Note:  The unit will notify the user that it has exited Ready Mode by giving 3 slow flashes 
(parking lights). 

Remote-starting 

Press the 

START

 button for approx. 1 second. The parking lights will come 

ON

 to inform you that the 

Remote Car Starter has received your signal. Approximately 5 seconds later, the engine will start. 
The parking lights will remain 

ON

 during the pre-programmed run time of the engine. If the vehicle 

does not start at the first attempt, the system will shut down, wait a few seconds and try to start the 
engine again. There will be 3 start attempts before the system gives up. 

Vehicle Presets 

Heater & Heated Seat 
When leaving the vehicle it is recommended to preset the accessory controls in preparation for the 
next remote start. Settings for the blower motor (fan), front and rear, as well as heated seats (if 
equipped) should not be left on 

HIGH

. It is recommended to leave the settings on 

LOW

 or 

MEDIUM

 

instead. 
Windshield Wipers & Radio & Headlights 
Certain vehicles require the radio and / or windshield wiper and / or headlight circuits to become 
energized while running under remote start. When leaving the vehicle you must ensure that the 
windshield wiper and headlight switches are 

OFF

. Leaving the headlight switch 

ON

 on certain types 

Summary of Contents for PS-3185SH










Reviews: