background image

P. 16 

User Guide

 

 

Diagnostics – Parking Light Flash Table 

Flashes 

Description 

 

Doors locked, alarm and starter kill armed. 

 

End of run time. 

 

TRUNK

 button pressed 

 

Start signal received by the system. 

 

Cold weather mode cancelled. 

 

Cannot start after maximum number of attempts is reached. 

 

Doors unlocked, alarm and starter kill disarmed. 

 

Run time cancelled. 

 

Exit remote valet. 

 

Exit ignition valet 

 

Remote start attempt cancelled by remote. 

 

Entering 

cold weather mode

 

Entering remote valet. 

 

Entering ignition valet 

 

+12 V where detected on the brake line and cranking was cancelled. 

 

Entering tach-programming mode 

 

New transmitter programmed. 

 

Tach programmed. 

 

A remote start was attempted while a tach or a vacuum signal was detected 

before cranking. 

 

Unit reset: occurs when the unit is reset to the factory defaults. 

10 

 

The hood switch line went to ground during cranking or run time. 

1 – pause – 2 

 

There was an attempt to start the vehicle while the system was in valet 

mode. 

2 – pause – 2 

 

There was an attempt to start the vehicle while the system was in home valet 

mode. 

ON solid 

 

Cold weather mode

: the brake pedal is being held down. 

ON 2 sec. 

 

The hood is up and the hood switch line went to ground. This is step one of 

the programming centre procedure. 

ON 3 sec. 

 

First press of the 

START/STOP

 button under safe start. 

ON 4 sec. 

 

Locking or unlocking a door (with door pulses configured to 4 sec.) 

ON 25 sec. 

 

The hood pin-switch has been pressed twice: the unit went into step 1 of the 

programming centre procedure, and no transmitter activity was detected for 

20 seconds. 

 

Or 

the Unit went into step 1 of the transmitter programming procedure and 

no activity was detected for a few seconds. The unit has exited the 

transmitter programming procedure.

 

Irregular 

 

If the unit gives irregular signals (1 to 10 flashes followed by a pause, 

followed by further flashes), the system is playing back start failure codes. 

This occurs when the hood pin-switch is pressed three times. 

Constant 

flashes 

up to 30 sec. 

 

In horn mode: alarm condition generated by an intrusion, by panic mode or 

when the system is powered up. 

Constant 

flashes 

up to 60 sec. 

 

In siren mode: alarm condition generated by an intrusion, by panic mode or 

when the system is powered up. 

 

Summary of Contents for PS-7020 TW

















Reviews: