background image

 

Politec S.r.l. | Manual Ales – Ver. 1.7.2 

15 

 

11. F.A.Q. 

 

 

I can’t find alignment 

o

 

Check no obstacles are placed between TX and RX and site 

conformation not gives itself an obstacle to installation; 

o

 

Check arrival supply tension to terminal block; 

o

 

Use a screened cable to supply barriers, connecting screen to 
GND on terminal block(it is suggested, if problem is not 

solved, to use two different screened cables, one to supply 

and one for alarm/tamper output); 

o

 

Check correct dimension of  cable used to supply barriers  

o

 

Make sure that no other external lights are interesting RX 
side, during function TEST (gate photocell, any other barrier, 

infrared lights, exc…). 

o

 

It is possible to increase barrier screening, connecting to 

GND a cable coming from the screw that link sensor base to 
metallic bracket; 

 

 

After best signal achieved 

(LEDs are fixed and buzzer 

sounds continuously) 

barrier stays in alarm  

o

 

Make sure RX and TX have same channel; 

o

 

Make sure that no other external lights are interesting RX 

side, during function TEST (gate photocell, any other barrier, 
infrared lights, exc…). 

o

 

Use a screened cable to supply barriers, connecting screen to 

GND on terminal block(it is suggested, if problem is not 

solved, to use two different screened cables, one to supply 
and one for alarm/tamper output); 

o

 

Check correct dimension of  cable used to supply barriers; 

o

 

It is possible to increase barrier screening, connecting to 
GND a cable coming from the screw that link sensor base to 

metallic bracket; 

 

 

System in alarm with fog 

or rain

 

o

 

Make sure environmental disqualification is activated; 

o

 

Make sure columns are well closed and check inside there 
are no presence of water or insects; 

o

 

Check the precision of alignment and in case remake 

alignment TEST, making sure that no other external lights 

are interesting RX side (gate photocell, any other barrier, 

infrared lights, exc…); 

o

 

To obtain a more precise alignment position a side of ales IR 
plastic cover in front of the lenses, during the alignment test, 

to have a double attenuation of beam; 

o

 

For long range protection is suggested the use of thermostat 

warranting an enough supply to it. 

 

 

 

 

Summary of Contents for ALES 120

















Reviews: