background image

11

SADRIN WS SMA

POLITEC | INSTALLATION MANUAL - VER.2.1

7.Batteries

7.1 WSI version

3.6V - 2.7Ah lithium batteries placed inside each column, on a special connection battery module, it is
possible to increase the number of batteries by inserting other modules.

7.2 WSE version

3.6V - 19Ah lithium battery placed in a special box, inserted at the top end of each column.

7.3 Battery life

NUMBER OF 

BEAMS

WSE

WSI

2

3 years ***

2 years *

4

3 years ***

1 year *

6

2.5 years ***

1.5 years **

8

2 years ***

1 year **

* value refers to 2 batteries 3.6 V - 2.7 mAh
** value refers to 4 batteries 3.6 V - 2.7 mAh
*** value refers to a 3.6 V - 19 Ah battery

N.B.:The low battery signal occurs as a local acoustic alert, during the alarm events of the barrier
and their sending through the radio transmitter if configured.
N.B.:Battery life can also vary due to other factors, such as if the radio transmitter is powered by
the column battery or by the specific climatic conditions of the installation area.
N.B.:The barrier is capable of operating with power up to 2.8V; if the voltage on the battery
measured under load is <3.4V, it means that the lithium battery is almost flat.

WSE

WSI

Summary of Contents for Sadrin WS Series

















Reviews: