background image

Even if you don’t have the room for full-size home theater

speakers, you still deserve great sound. This is the theory behind

the development of “subwoofer/satellite” systems, whose coffee-

cup-sized satellites can be placed conveniently and invisibly

almost anywhere. These systems produce remarkable sound for

their size, but even the best “sub/sat” systems have never quite

equaled the performance of full-size speakers. 

Knowing this, we set out to develop the ultimate “sub/sat” system.

One with the convenience of a “sub/sat” system, and the

performance you expect from Polk Audio. 

Ultimately, we found that the only way to achieve our

goal was to design not only the speaker system but the

preamp, surround processor, and amplifiers as well.

By 

optimizing 

the speakers and electronics for each

other we achieved a much higher level of performance than any

previous sub/sat system! 

When we were finished, we found we had created something 

entirely new: a no-compromise sub/sat surround system with all

of the electronics for a high-performance Dolby Digital home

theatre—integrated into a single, complete system. 

We call it the RM Digital Solution: “An Intelligent A/V Pre-amp

Processor and High Performance Loudspeaker System.” With

the RMDS-1, you have everything you need—except sources.

There’s no need to choose a receiver or separate surround

processor or multi-channel power amplifier. With the RMDS-1

you already have them. 

They’re built-in.

And, most importantly,

you know that they were designed specifically for each other to

deliver no-compromise performance.

You don’t need an advanced degree in digital electronics to get the

most out of this system. We’ve done the work for you. The RMDS-1

is a complete system. Everything is pre-optimized to achieve

the best possible performance. No complicated

setup procedures are required. 

Simply plug everything in, and enjoy!

S

IMPLY

C

OMPLETE

H

OME

T

HEATER

:

T

HE

RM D

IGITAL

S

OLUTION

P

ERFORMANCE

C

ONVENIENCE

S

IMPLICITY

www.polkaudio.com

3

Summary of Contents for RMDS1

































Reviews: