Pololu Corporation Zumo User Manual Download

Page: 4 / 12

2. What you will need

In addition to the Zumo chassis kit, you will require these items to construct a working robot:

Assembly tools

• Small Phillips screwdriver

• 3 mm Allen wrench (hex key)

Additional required components (not included with the kit)

• Two

micro metal gearmotors

[https://www.pololu.com/category/60/micro-metal-gearmotors]

(we

recommend 100:1, 75:1, or 50:1 HP or HPCB versions)

• Four AA batteries (we recommend rechargeable

AA NiMH cells

[https://www.pololu.com/

product/1003]

)

• Electronics to control the motors (e.g. the

DRV8833 dual motor driver carrier

[https://www.pololu.com/product/2130]

)

Additional optional components (not included with the kit)

• One

basic sumo blade for Zumo chassis

[https://www.pololu.com/product/1410]

Please see the

product description

[https://www.pololu.com/product/1418]

for the chassis kit for more

information and recommendations about selecting these components.

You will also likely need a soldering iron to connect your motors and batteries to your
electronics.

Pololu Zumo Chassis User’s Guide

2. What you will need

Page 4 of 12

Summary of Contents for Zumo













Search results

Summary of Contents for Zumo

Reviews:

Related manuals for Zumo

Brands by name

Popular brands

Pololu Corporation Zumo, User Manual

Search results

Summary of Contents for Zumo

Reviews:

Related manuals for Zumo

Brands by name

Popular brands