3. IRONING
3.1 Ensure that the instructions in Chapters 1
and 2 have been followed.
3.2 Plug the connector on the other end of
the power cord into a suitable socket with an
earth connection.
3.3 Set the temperature adjustment dial (3).
The iron temperature light will turn on (2).
3.2 When the iron has reached the selected
temperature, the heating indicator light will
turn off.
3.4 The appliance is ready for use.
4. CONTINUOUS STEAM IRONING
Steam ironing can be selected by moving the
iron temperature adjustment knob to the •••
or the MAX position. The amount of steam
can be adjusted with the steam adjustment:
when moved forward, the amount of steam
will increase, when moved backward, it will
decrease (4).
5. STEAM JET
To make ironing faster and easier the STEAM
JET function can be activated, which is ideal
for removing the most stubborn wrinkles. To
activate it, press the button
(5-6).
If the iron temperature light comes on while
this function is being used, wait until it turns
back off (the iron returns to the desired
temperature).
6. SPRAY FUNCTION
The Spray function is perfect for dampening
the entire surface of the fabric in a uniform
manner, making it easier to remove stubborn
wrinkles. To activate it, press the button
(7-8).
7. VERTICAL IRONING
The iron may be used in the vertical position
to remove creases from fabrics and/or to
refresh fabric fibres, eliminating any residual
odours.
8. AUTO SHUT-OFF FUNCTION
When the Polti Vaporella Quick&Comfort is
not used, the Auto Shut-Off safety function
activates. The time before activation varies
based on the position of the iron and starts
from the last completed action:
Vertical position: around 8 minutes
Resting or horizontal position: around 1
minute.
When the Auto Shut-Off function is activated,
the heating indicator light (9) will flash and
the iron will go into stand-by
.
Simply move the device to turn it back on.
Before ironing again, wait until the heating
light turns off.
9. OUT OF WATER
When the device no longer dispenses steam,
it means that there is no water in the tank.
To begin using steam again, simply remove
the power supply from the electric socket
and fill the tank as described in chapter 1.
10. SELF CLEAN SYSTEM
The Polti Vaporella Quick&Comfort Self Clean
system ensures removal of limescale, thus
guaranteeing a better supply of steam and
avoiding the leakage of dirt from holes in the
plate which can create stains.
Regularly run the Self Clean cycle to ensure
better performance and durability over time.
It is recommended that the cycle be run at
least once a month.
In any case, it is possible to perform the
cleaning cycle at any time.
Before running the cleaning cycle, make sure
you have a large receptacle or bowl on hand
to collect the water, steam and limescale that
will come out from the iron during the pro-
cess, thus avoiding the wetting of the ironing
board or surface on which you are ironing.
When first using the steam, there may be
some drops of water leaking out of the
plate, this is due to thermal stabilization. It is
recommended that the first jets of steam
are not directed onto the fabric that needs
ironing.
ATTENTION: When the temperature is set
to the levels •• / • / MIN, the steam (4) must
be set to the zero position (steam off/dry
ironing)
otherwise water could leak out
with the steam.
Activate the Steam Jet every few seconds,
one after another.
ATTENTION: The STEAM JET function only
works when the temperature is set to the
••• or MAX level.
The heating indicator light turns on and off
during use. This indicates that the electrical
resistor has started to work to keep the
temperature in the iron steady: continue
ironing normally.
E
N
G
L
IS
H
| 23 |
VAPORELLA QUICK&COMFORT - M0S12153 - W1PV - 1V03_FEV 1000-950.qxd 09/03/2021 16:40 Pagina 23
