Poly-Tex FieldPro Gothic High Tunnel 20 Installation Instructions Manual Download

Page: 2 / 41

$background image$

Thank you for purchasing a FieldPro Gothic High Tunnel Greenhouse.
The FieldPro has been carefully engineered to provide years of faithful
service.

This installation manual covers the 20



and 24



FieldPro Series. The main

structural components are different for each FieldPro Series, however, both
units share most smaller fittings and hardware. As such, the assembly pro-
cedure of a 20



unit is very similar to a 24



unit.

Wherever an assembly procedure or specific part is different between a 20



unit and a 24



unit — the differences are clearly explained.

Where this icon appears you will be alerted to

a useful installation tip or an optional way of

performing an installation operation.

Where this icon appears you will be alerted to

a Time-Saving tip that will help speed up the

FieldPro installation.

Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Overview of FieldPro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Gothic 20



Main Components Identification. . . . . . . . . . . . . . . . . . . . 6

Gothic 24



Main Components Identification . . . . . . . . . . . . . . . . . . . . .7

Standard Fittings and Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Building Site Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Layout of Ground Support Locations . . . . . . . . . . . . . . . . . . . . . . . . . .10

Ground Stake installation Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Ground Stake and Ground Stand Installation . . . . . . . . . . . . . . . . . . . 12

Ground Stake Installation in Concrete Pier . . . . . . . . . . . . . . . . . . . . . 13

Building Side Sub-Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Building Main Frame Sections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Erecting Main Frame Sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Adding Diagonal Braces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Side Purlin Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Adding Main Frames and Side Purlins. . . . . . . . . . . . . . . . . . . . . . . . . 19

Peak Purlin Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 –21

Truss Frame Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 –23

Installing Wood Side Rails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 –25

Plain End Wall Wiggle Wire Base Material Installation . . . . . . . . . . 26

Plain End Wall Poly Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Open Doorway – Part 1 and Part 2 . . . . . . . . . . . . . . . . . . . . . . 28 –29

Wiggle Wire Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Installation of Roof Poly – General Instructions . . . . . . . . . . . . . . . . . 31

Installing Roof Poly on FieldPro with Roll-Up Side Curtain . . . . . . . 32

Installing Ground-to-Ground Roof Poly . . . . . . . . . . . . . . . . . . . . . . . 33

Optional Door Kit w/ Metal Frame Installation . . . . . . . . . . . . . . 34–37

Optional Roll-Up Curtain Installation . . . . . . . . . . . . . . . . . . . . . . 38 –41

Introduction

Index

Summary of Contents for FieldPro Gothic High Tunnel 20










































Search results

Summary of Contents for FieldPro Gothic High Tunnel 20

Reviews:

Related manuals for FieldPro Gothic High Tunnel 20

Brands by name

Popular brands

Poly-Tex FieldPro Gothic High Tunnel 20, Installation Instructions Manual

Search results

Summary of Contents for FieldPro Gothic High Tunnel 20

Reviews:

Related manuals for FieldPro Gothic High Tunnel 20

Brands by name

Popular brands