background image

Procedure

1.

In the system web interface, go to 

Security

 > 

Certificates

.

2.

Locate the certificate you want to delete and select 

Delete

 

 in the same row as the certificate.

Caution:

You can’t undo this action.

3.

Confirm by selecting 

Delete

.

A message indicates that the system deleted the certificate.

Certificate Revocation

During certificate validation, your system checks whether certificates used for secure communications are
revoked by their issuing CAs.

Your system can check certificate revocation status with the following standard method:

Certificate Revocation List (CRL)

: File containing a list of certificates revoked by their issuing CA.

You must manually upload CRLs to your system.

Manually Upload a CRL

You can use CRLs to perform certificate revocation checks on your system.

Uploading a CRL fails unless you install all of the certificates in the issuing CA’s chain of trust for that

CRL.

This option is not available if your CRL is provisioned to the system.

Procedure

1.

In the system web interface, go to 

Security

 > 

Certificates

.

2.

Configure the following settings:

Setting

Description

Revocation Method

To use the CRL revocation method, select 

CRL

.

Allow Incomplete Revocation Checks

When enabled, a certificate in the chain of trust
validates without a revocation check if no
corresponding CRL from the issuing CA is installed.

3.

Select 

Save

.

4.

Select 

Upload CRL File

 to add a CRL.

You aren’t limited to how many CRLs you can install, but you can only upload 10 at a time.

Successfully-uploaded CRLs display on the page and include information about the issuing CA, when the

CRL was updated, and when it’s scheduled to update again.

Delete a CRL

You can remove CRLs that were previously uploaded on the system.

This option is not available if your CRL is provisioned to the system.

Procedure

1.

In the system web interface, go to 

Security

 > 

Certificates

.

Securing the System

57

Summary of Contents for G7500
























































































































Reviews: