background image

 

1725-36127-001-F.doc 

About this Guide 

 

The Outdoor Base Station is designed to withstand environmental 
hazards such as rain and excessive heat and cold. The outdoor 
enclosure is mounted into position and the Base Station is then 
installed within it. The entire unit is then referred to as an Outdoor 
Base Station.  
This document covers the installation of the Outdoor Base Station 
in a variety of situations. It supplements the installation 
documentation for the SpectraLink 6000 System using either the 
SpectraLink 6300 MCU or the SpectraLink 6100 MCU. 

Polycom Corporation Model Numbers 

This document covers the following registered model numbers: 
RCO400, RCO410, RHO400 

Related Documents 

SpectraLink 6100 MCU: Installation and Operation

 (1725-36097-001) 

SpectraLink 6300 MCU: Installation

 (1725-36122-001) 

Available at 

http://www.polycom.com/usa/en/support/voice/proprietary_
wireless/proprietary_wireless.html

 

Contacting Polycom 

Polycom wants every customer to have a successful installation. 
Please refer questions to the Customer Support Hotline at  
(800) 775-5330. The hotline is open Monday through Friday,  
6 a.m. to 6 p.m. Mountain time. 

Summary of Contents for SpectraLink 6000 System













Reviews: