background image

Figure 12 

                                                                   

     

     

     

     

     

           

           

           

           

          3032 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 13 

2-2-9 Connecting the Power Cord

Fig.12, 13 

and 14

 

★ 

★ 

★ 

★ 

Do  not  place  stress  or  strain  on  the  power 

cord. These will damage the cord and cause 

a danger to the user.

 

  

 

1.

 

Turn  the  main  switch 

  to  “O”  (off)  before 

connecting the power cord. 

2.

 

Insert the power cord plug 

 into the electrical 

connector 

3.

 

Insert  the  power  cord 

④ 

into  an  electrical 

receptacle (5). 

4.

 

Insert the BNC connector plug 

 into the BNC 

connector jack 

  Ensure  the  power  cord  is  connected  to  a 

grounded receptacle. 

Use  of  an  electrical  surge  suppressor  receptacle 

is highly recommended. 

 

2-2-10 Replacing the Fuse (Figures 12 & 13

 

       

Turn  the  main  switch 

  to  “O”  (off)  before 

replacing  the  fuse.  Unplug  the  power  cord. 

Rotate  the  fuse  holder 

  out  of  the  base 

 

with a  flat  edge screwdriver, replace the  fuse, 

then insert the fuse holder and tighten. 

Fuse rating: 250V

500mA. 

 

Figure 14 

Summary of Contents for 3032 series
























Reviews: