Automatic boiler for wood pellets
4
IMPORTANT NOTES
This product may only be put into operation by an installation organization trained by the manufacturer.
This product may only be operated by adult persons, duly acquainted with the way the product is controlled and duly
acquainted also with these Instructions. If you adhere to the below mentioned principles, the product will serve you
reliably to your full satisfaction.
1)
It is prohibited to intervene in any way in the structure or electrical installation of products. Having the
equipment been disconnected from the electric network, the power supply cord has to be plugged from the
mains outlet.
2)
It is prohibited to use inflammable liquids for ignition.
3)
No inflammable materials may be stored on the boiler; neither may they be stored within the distance of 1,500
mm from the boiler (except for operating metal fuel bin).
4)
In order to preserve long-term service life of the boiler body, it is not recommended to operate the boiler
frequently under the temperature of 55°C, if the boiler is not protected with a primary circuit. The temperature of
55°C should be considered as the minimum temperature.
5)
The check how the boiler is filled with fuel is only visual. Any verification with touch is prohibited as it may result
in injury.
6)
Never open door of the boiler if there is an ignition process.
7)
The door of the boiler has to be always tightly closed. If you´ll perform any check, open the door carefully to
prevent from getting jeopardized by gathered products of combustion or to prevent any sparks flying out from
the boiler from being the cause of any accident. Open the door slowly in order to get the combustion chamber
aerated towards the chimney. This procedure has to be adhered to when the ash is being removed from the ash
pan's space.
8)
If any work which generates inflammable vapours takes place in the boiler room (glueing the floor, etc.), the
boiler has to be out of operation and the fire has to be burnt out in the boiler.
9)
Having the heating season been finished, clean the boiler thoroughly as per the chapter Maintenance. Products of
combustion stuck to the walls of the exchanger may act corrosively for the whole period of time when the boiler
will be out of operation. If the burner is not cleaned, this may have effect on faulty combustion. We recommend
hire a specialized company to perform this work.
10)
If you work on or near to the mechanically movable parts (fuel feeder, etc.), ensure safe disconnection of the
equipment from electric voltage. There is a risk of injury.
11)
You should always operate the boiler only under parameters and in harmony with recommendations given in
these instructions for installation and operation. If the boiler works in the AUTO mode and if there is a failure of
current, the boiler will start operation again with the electric firing programme (if this programme has been
installed) after the delivery of electric current is restored.
12)
The manufacturer does not assume any liability for errors and subsequent damage caused by unskilled operation
of the equipment or by infringement of principles given in these instructions for installation and operation or by
infringement of generally binding standards and regulations or by using inadequate fuel.
13)
If the boiler is moved or otherwise handled with, safety regulations which apply to handling with heavy loads
have to be adhered to.
14)
It is prohibited to place heavy loads on jacketing boiler and to step on it. It is recommended to remove the
protective foil after all the building and installation work has been completely finished.
15)
External ashtray has to be firmly connected to a boiler fitting while in the operation. Cover of this ashtray has to
be tightly closed. There could be a dangerous escape of combustion gases into a boiler room.
Summary of Contents for KP 12S
