WORK AREA SET-UP
UNPACK AND SET-UP(CONT.)
1. Verify that work area has adequate lighting for the job.
2. Make sure work area is free of flammable liquids, vapors or dust that may ignite. Sparks can be generated during drain cleaner
operation. Do not work in area until these sources of ignition have been identified and corrected.
3. Choose a firm, stable location for the appliance and operator that will remain relatively dry. Do not use the appliance while standing in
water. If needed, remove the water from the work area.
4. Verify the electrical outlet is properly grounded. A three-prong or gfci outlet may not be properly grounded. If in doubt, have outlet
inspected by a licensed electrician.
5. Make sure there is a clear, unobstructed path from the drain cleaner to the electrical outlet. 6. Inspect the drain to be cleaned. If
possible, determine the best access point(s) to the drain, the size(s) and length(s) of the drain, distance to tanks or mainlines, the nature
of the blockage, presence of drain cleaning chemicals or other chemicals, etc.
7. If there are chemicals present in the drain, read and adhere to the specific safety measures required to work around those chemicals.
Contact the chemical manufacturer for required safety instructions and information.
8. If necessary, remove fixture (toilet, sink, etc.) to allow access to the drain. Do not feed the cable through a fixture. This could damage
the drain cleaner and the fixture.
9. Determine the correct drain cleaning cable size for the drain cleaning job. See cable/pipe size chart below.
10. If needed, place protective covers over the work area floor. Cleaning the clogged drain can be a messy operation.
11. Make sure that the drain cleaner handle is locked into the upright position for transport. If the drain cleaner needs to be lifted, use
proper lifting techniques or seek assistance if needed. Use caution when moving equipment up and down stairs. Wear appropriate
footwear to help prevent slipping on floor.
12. To prevent cable from whipping, place drain cleaner within 2 feet of drain line or thread cable through guide (not included). The greater
the distance from the drain access, the higher the risk of the cable twisting or kinking.
13. If the drain cleaner cannot be placed within 2 feet of the drain access, use appropriate-sized pipes and fittings to extend the drain
access back to within 2 feet of the drum opening. Improper cable support can allow the cable to kink and twist and can damage the cable
or injure the operator.
14. If needed, set up barriers to keep bystanders away from the drain cleaner and work area during operation.
15. Select proper cutting tool.
16. Install the cutting tool to the end of the cable. Slide the base of the cutting tool into the slot at the end of the cable. Fasten together
using a screwdriver.
17. Position the foot switch for easy accessibility. You must be able to hold and control the cable, control the foot switch, and reach the
rotation switch.
18. Confirm that the rotation switch is in the off position.
19. Run the cord along the clear path. With dry hands, plug the drain cleaner into a properly grounded outlet. Keep all connections dry and
off the ground.
20. If the power cord is not long enough, use an extension cord that is in good condition and has a three prong plug similar to the
One supplied on the drain cleaner. Keep the connection off the ground to prevent it from accidentally getting wet.
21. Also verify that the extension cord is rated for outdoor use and contains a w or w-a in the cord designation (i.E. Sow).
22. Verify the extension cord has sufficient wire size (16 awg for 50′ or less, 14 awg for 50′ – 100′ long). Undersized wires can overheat,
Melting the insulation or causing a fire or other damage.
23. When using an extension cord, the gfci on the drain cleaner does not protect the extension cord. If the outlet is not gfci protected,
Use a plug-in type gfci between the outlet and the extension cord. This will reduce the risk of shock if there is a fault in the extension cord.
Cable Size
Pipe Size
Typical Applications
Roof stacks and small floor drains (no roots)
Roof stacks, laundry lines and small drains (no roots)
1/2” (included)
3/8” (not included)
2” to 4”
1-1/2” to 3”
