background image

13 

© PORT Technology by Schindler Ltd - Oct 20, 2017 

 

 

4 Reliability

 

EMC

 

The board must comply with the requirements of EN12015:2004 and EN12016:2004. 

Tests are performed at system level. 

 

Climatic conditions

 

Operating temperature:

 

ambient temperatures of 0 to 60 °C. 

Relative humidity:

 

yearly average less or equal to 65%, 60 days 85%.

 

Altitude:

 

up to 2000 m above sea level. 

 

Climatic tests are performed at system level. 

 

 

Certifications

 

The PCR-TWN4 comply from 15.19 / 15.21 and RSS-Gen clause 8.4. 
 

The PCR-TWN4 complies with the following requirements:

 

  FCC (Federal Communications Commission) Part 15 

  IC (Industry Canada) RSS-102 

 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 

1.  This device may not cause harmful interference 
2.  This  device must accept any interference received, including interference that may cause 

undesired operation 

 
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and 
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two 
conditions: 

  This device may not cause interference. 

  This device must accept any interference, including interference that may cause undesired 

operation of the device 

 

Changes or modification not expressly approved by the party responsible for compliance could void the 
user’s authority to operate the equipment. 

 

FCC ID: XFIPCRTWN4 
IC ID: 9114A-PCRTWN4 

 

 
 

 

 

Summary of Contents for PCR-TWN4
















Reviews: