background image

5

Safety and  contents

Pay special attention to operation in the rain or just after the rain as the ground may be 
slippery.

If you slip or fall to the ground or into a hole, release the throttle lever immediately.

Be careful not to drop the machine or hit it against obstacles.

Before proceeding to adjust or repair the machine, be sure to stop the engine and detach the 
spark plug cap from the spark plug.

When the machine is placed in storage for a long time, drain fuel from the fuel tank and 
carburettor, clean the parts, move the machine to a safe place and confirm that the engine is 
cooled down.

Make periodic inspections to assure safe and efficient operation. For a thorough inspection of 
your machine, please contact a dealer.

Keep the machine away from fire or sparks.

 

 WARNING: The cutting area is still dangerous while the  

 

 machine is coasting to a stop.

CONTENTS

Important safety instructions 

2 - 6

Specifications 7
Assembly of RufCut 

7

Powerstrim mulching head and adjusting line 

9

Operation 12
Exploded drawings 

15

Maintenance 17
Troubleshooting and spare parts 

18

Certificate of conformity 

19

!

Summary of Contents for Rufcut





















Reviews: