background image

12

PORTER-CABLE LIMITED ONE YEAR WARRANTY

Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original
purchase. We will repair or replace at our option, any part or parts of the product and accessories
covered under this warranty which, after examination, proves to be defective in workmanship or
material during the warranty period. For repair or replacement return the complete tool or accessory,
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.
Proof of purchase may be required. This warranty does not apply to repair or replacement required
due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service
Centers or Authorized Service Stations.

ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE
OF PURCHASE.

To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,
4825 Highway 45 North, P.O. Box 2468, Jackson, Tennessee 38302-2468; Attention: Product
Service. THE FOREGOING OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR
ANY IMPLIED WARRANTY AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE
LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow
limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.

This warranty gives you specific legal rights and you may also have other legal rights which vary
from state to state.

ACCESSORIES

The 

Model 7414 Sander

can be used with various sander accessories

available from your industrial supplier. The 

Model 7414 Sander

can also be

used as a grinder with the appropriate 7" or 9" 

TYPE 27

wheel guard

accessories (as shown in the chart below). ALL ACCESSORIES MUST BE
RATED FOR 6,000 RPM (or higher), and GRINDING WHEELS MUST BE
USED WITH THE APPROPRIATE PORTER-CABLE GUARDS (as shown in
the following chart).

The following accessories are available from your Porter-Cable Distributor or
Service Center.

PORTER-CABLE CATALOG NO.

DESCRIPTION

54367

7" Wheel Guard Type 27

54374

9" Wheel Guard, Type 27

54357

7" Rubber Back-up Pad

55741

7" Abrasive Back-Up Kit

55747

Retaining Nut

283800 - 07-31-00.QXD  9/23/02  1:35 PM  Page 12

Summary of Contents for 7414














Reviews: