background image

16 - ENG

A07300

STORAGE

Before you store the air compressor, 
make sure you do the following:

1.  Review the "Maintenance" 

section on the preceding 
pages and perform scheduled 
maintenance as necessary. 

2.  Set the On/Off switch to OFF (O) 

and unplug unit.

3.  Turn the regulator 

counterclockwise and set the 
outlet pressure to zero.

4.  Remove the air tool or accessory.

5.  Pull ring on safety valve allowing 

air to bleed from the tank until 
tank pressure is approximately 20 
psi. Release safety valve ring.

6.  Drain water from air tank by 

opening drain valve on bottom of 
tank.

Risk of Bursting. 
Water will 

condense in the air tank.  If not 
drained, water will corrode and 
weaken the air tank causing a risk 
of air tank rupture.

7.  After the water has been drained, 

close drain valve by turning 
clockwise.  

NOTE: 

If drain valve is plugged, 

release all air pressure.  The valve 
can then be removed, cleaned, then 
reinstalled.

8.

 

Protect the electrical cord and 
air hose from damage (such as 
being stepped on or run over).  
Wind them loosely around the 
compressor handle.

9.  Store the air compressor in a 

clean and dry location.

Summary of Contents for CFBN125A



















Reviews: