background image

8- ENG

A08193

Accessories for this unit are available at the store the unit was purchased.

ACCESSORIES

GLOSSARY

Become familiar with these terms before operating the unit.

CFM

:  Cubic feet per minute.

SCFM:

  Standard cubic feet per minute; a unit of measure of air delivery.

PSIG:

  Pounds per square inch gauge; a unit of measure of pressure.

Code Certification: 

Products that bear one or more of the following marks: UL, 

CUL, ETL, CETL, have been evaluated by OSHA certified independent safety 

laboratories and meet the applicable Underwriters Laboratories Standards for 

Safety.

Cut-In Pressure:

  While the motor is off, air tank pressure drops as you 

continue to use your accessory. When the tank pressure drops to a certain low 

level the motor will restart automatically.  The low pressure at which the motor 

automatically restarts is called "cut-in" pressure.

Cut-Out Pressure:

  When an air compressor is turned on and begins to run, 

air pressure in the air tank begins to build.  It builds to a certain high pressure 

before the motor automatically shuts off - protecting your air tank from 

pressure higher than its capacity.  The high pressure at which the motor shuts 

off is called "cut-out" pressure.

Branch Circuit: 

Circuit carrying electricity from electrical panel to outlet.

DUTY CYCLE

This air compressor pump is capable of running continuously. However, to 

prolong the life of your air compressor, it is recommended that a 50%-75% 

average duty cycle be maintained; that is, the air compressor pump should not 

run more than 30-45 minutes in any given hour.

SPECIFICATIONS

    Model No. 

C3550

    Running Horsepower 

1.3 

    Bore 

2.363

    Stroke 

0.890 

*    Voltage-Single Phase 

120

*  *  Minimum Branch Circuit Requirement 

15 amps

*    Fuse Type 

Time Delay 

    Air Tank Capacity (Gallon) 

4.5 ASME 

    Approximate Cut-in Pressure 

120 PSIG 

    Approximate Cut-out Pressure 

150 PSIG

    SCFM @ 40 PSIG 

5.7 

    SCFM @ 90 PSIG 

4.4

One accessory available for this 
unit is the Job Boss ™ Mobility Kit, 
this accessory includes retractable 
handle, comfort grip, mounting 
bracket, pneumatic wheels, shoulder 
bolts, and all associated hardware 
needed to make this unit more 
mobile.

Unit shown with 
PTA50 Mobility kit, 
sold separately.

Summary of Contents for JOB BOSS C3550



























Reviews: