22.) Since the vibration produced by the inflator may cause it to “walk”, do not operate on
a high shelf or other surface. Operate at ground or bench level only.
GENERAL SAFETY RULES
•
KEEP WORK AREA CLEAN.
Cluttered areas and benches invite injuries.
•
CONSIDER WORK AREA ENVIRONMENT.
Donʼt expose power tools to rain. Donʼt use
power tools in damp or wet locations. Keep work area well lit. Do not use tool in presence
of flammable liquids or gases.
•
GUARD AGAINST ELECTRIC SHOCK
. Prevent body contact with grounded surfaces.
For example; pipes, radiators, ranges, and refrigerator enclosures.
•
KEEP CHILDREN AWAY.
Do not let visitors contact tool or extension cord. All visitors
should be kept away from work area.
•
STORE IDLE TOOLS.
When not in use, tools should be stored in dry, and high or locked-
up place — out of reach of children.
•
DONʼT FORCE TOOL.
It will do the job better and safer at the rate for which it was intended.
•
USE RIGHT TOOL.
Donʼt force small tool or attachment to do the job of a heavy-duty
tool. Donʼt use tool for purpose not intended.
•
DRESS PROPERLY.
Do not wear loose clothing or jewelry. They can be caught in
moving parts. Rubber gloves and non-skid footwear are recommended when working
outdoors. Wear protective hair covering to contain long hair.
•
USE SAFETY GLASSES.
Also use face or dust mask if operation is dusty.
•
DONʼT ABUSE CORD.
Never carry tool by cord or yank it to disconnect from receptacle.
Keep cord from heat, oil, and sharp edges.
•
SECURE WORK.
Use clamps or a vise to hold work. Itʼs safer than using your hand and it
frees both hands to operate tool.
•
DONʼT OVERREACH.
Keep proper footing and balance at all times.
•
MAINTAIN TOOLS WITH CARE.
Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories. Inspect tool
cords periodically and if damaged, have repaired by authorized service facility. Inspect
extension cords periodically and replace if damaged. Keep handles dry, clean, and free
from oil and grease.
•
DISCONNECT OR LOCK OFF TOOLS
when not in use, before servicing, and when
changing accessories, such as blades, bits, cutters.
•
REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that
keys and adjusting wrenches are removed from tool before turning it on.
•
AVOID UNINTENTIONAL STARTING.
Donʼt carry tool with finger on switch. Be sure
switch is off when plugging in.
•
When using an extension cord, be sure to use one heavy enough to carry the current
your product will draw. An undersized cord will cause a drop in line voltage resulting in
loss of power and overheating. The following table shows the correct size to use
depending on cord length and nameplate ampere rating. If in doubt, use the next
heavier gauge. The smaller the gauge number, the heavier the cord.
Recommended Minimum Wire Size for Extension Cords
Total Length of Cord
25 ft.
50 ft.
75 ft.
100 ft.
125 ft.
150 ft.
175 ft.
7.6 m
15.2 m
22.9 m
30.5 m
38.1 m
45.7 m
53.3 m
Wire Size AWG
18
18
16
16
14
14
12
•
OUTDOOR USE EXTENSION CORDS.
When tools are used outdoors, use only
extension cords intended for use outdoors and so marked.
•
STAY ALERT.
Watch what you are doing. Use common sense. Do not operate tool when
you are tired.
•
CHECK DAMAGED PARTS.
Before further use of the tool, a guard or other part that is
damaged should be carefully checked to determine that it will operate properly and
perform its intended function. Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other conditions that may affect its operation.
A guard or other part that is damaged should be properly repaired or replaced by an
authorized service center unless otherwise indicated elsewhere in this instruction manual.
3
90577349 PCC583B Inflator.qxd:??????-00 BDL500 laser 7/22/11 3:06 PM Page 3
