background image

Eurekaweg 4 2991 ZB  Barendrecht 

T +31 (0)180 629009 

info@poseidon-bv.nl

 

www.poseidon-bv.nl 

Ordernumber 

 

Date 
25-01-2015 

Ref.erence 
STA-STF 

Version 

Status 
Final 

Page 

20

 of 

20

 

 

 
6

 

Service and spare parts  

 
 

We offer 3 spare parts kits; 
 

1)   

Emergency kit

, for each seal, existing out of;  

a.

 

2 pc Split seals. (item 12) 

b.

 

Tube with grease 

This kit is to be used in emergency cases were usually the vessel stays in the water 
and the shaft is not demounted.  
 

2)   

Small spare kit

 for each seal, existing out of; 

a.  2 Pc Endless seals (item 12) 
b.  Stand by seal rubber (item 13) 
c.

 

O-rings (item 11) 

d.

 

Gasket (item 14 and 15) 

e.

 

Tube grease  

This kit is to be used when an overhaul is made but were the wearing liners are still in 
a good condition  
 

 

3)   

Large spare kit

  

Note: this kit is the same as the above kit added with a liner 

a.

 

2 Pc Endless seals (item 12) 

b.

 

Stand by seal rubber (item 13) 

c.

 

O-rings (item 11) 

d.

 

Gasket (item 14 and 15) 

e.

 

Tube grease 

f.

 

SS 316 wearing liner (item 2) with a ceramic (excl. clamping ring 

Item 3) 

 

Summary of Contents for Pegasus Deluxe






















Reviews: