background image

PosiPin 1

TABLE OF CONTENTS

Installation .......................................................................... 2

Mounting and Wiring  ................................................................ 2
Mounting on Metal Surfaces ..................................................... 2
Technical Specifications ........................................................... 3
Feedback .................................................................................. 5
Resetting to Default .................................................................. 5
Card Presentation Test  ............................................................ 5

System Programming  ........................................................ 6

Section [001] Card/Code Options ............................................. 6
Section [002] Door Lock Control  .............................................. 7
Section [003] Access Granted Options  .................................... 7
Section [004] Display on Card Read  ........................................ 8
Section [005] Keypad Lockout .................................................. 9
Section [101] Buzzer Setting  .................................................... 9
Section [102] Face Light Intensity  ............................................ 9
Section [103] Face Light Operation .......................................... 9
Section [104] Face Light Colour  ............................................. 10
Section [200] Changing the Installer Code ............................. 10
Resetting the Installer and Master Codes to Default .............. 10

Master Programming  ....................................................... 11

Sections [201] and [202] Changing the Master Codes ........... 11
Section [203] User Code Programming .................................. 11
Deleting a User Code  ............................................................. 13
Section [204] User Code Reset .............................................. 14

User Operation  ................................................................. 15

User Access  ........................................................................... 15
Panic Alarm  ............................................................................ 16

User Code Table  ............................................................... 17

Warranty ............................................................................ 19

Summary of Contents for CR-R885-S
























Reviews: