background image

 

 

Part 14

USING THE TOUCH POS 

APPLICATION ENVIRONMENT 

It is 

very

 important that you check the following operational 

guidelines: 

Ventilation 

This terminal must 

NOT

 be operated in an environment with 

restricted ventilation. The installation should be such that there is at least 
25mm air clearance around any top or side ventilation holes. The installation 
must also be such that there is a free flow of air around the unit at 

ALL

 times. 

Operating Environment 

The equipment must not be operated or stored in extremes of both 

temperature and humidity/moisture. (Operating range 5°C to 40°C and up to 
80% humidity – non condensing) 

UPS Battery (option) 

General care: 

The UPS battery is consumables beyond product warranty. Please 

definitely observe the alerts in beginning of this manual. If the equipment is to 
be  powered off for  more than few days, please always 

disconnect

 the battery 

from the system. Reconnect it and turn on the system to recharge the battery 
for 1 ~ 2 hours every 3 months for temperature lower than 30

°

C. Recharge for 

1 ~ 2 hours every month for temperature over 30

°

C. Temperature above 

40°C 

must be strictly avoided

 as it could cause termination of battery life and 

unexpected result even if the battery is not in work. The UPS battery can 
support basically the data preservation and smooth running of the system 
during intermittent or few minutes (3 ~ 8 min. for TP/LT-5600/5700/5800 or 2 
~ 6 min. for TP/LT-8000 depending on loading and battery condition) power 
failure. 

Battery replacement: 

In the preloaded OS for a Jiva system, there is a built in utility Power 

Manager that will  interface the UPS battery  monitor status with user. When 
battery monitor disables the battery charging as designed while the UPS 
function of the system is originally  enabled, in other words the UPS battery is 
found out of order if actually installed,  there will be a popup message  as the 
picture at right asking the user to agree disabling the 
UPS function. The system will operate under 
deactivated UPS function no matter agreed or not. 
However, the monitoring goes on and the popup 
message will come back  on next system power up boot if not agreed. In any 
case, please replace the used up UPS battery at power off if the battery is well 

Summary of Contents for Jiva LT-5600





















Reviews: