background image

 

 

Part 1 

 
 
 
 
 

FCC Notes: 

This equipment generates, uses, and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions manual, may cause interference 
to radio communications. It has been tested and found to comply with limits for a Class 
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to 
provide reasonable protection against interference when operated in a commercial 
environment. Operation of this equipment in a residential area is likely to cause 
interference in which case the user at his own expense will be required to take whatever 
measures to correct the interference. 

Warranty Limits: 

 

Warranty terminates automatically when  any person other than the authorized 
technicians opens the  machine. The user should consult his/her dealer for the problem 
happened. Warranty voids if the user does not follow the instructions in application of 
this merchandise. The manufacturer is by no means responsible for any damage or 
hazard caused by improper application. 

About This Manual: 

Posiflex Technologies, Inc. has made every effort for the accuracy of the content in this 
manual. However, Posiflex Technologies, Inc. will assume no liability for any

 

technical 

inaccuracies or editorial or other errors or omissions contained herein, nor for direct, 
indirect, incidental, consequential or otherwise damages, including without limitation 
loss of data or profits, resulting from furnishing, performance, or use of this material.

 

This information is provided  “as is” and Posiflex Technologies, Inc. expressly 
disclaims any warranties, expressed, implied or statutory, including without limitation 
implied warranties of merchantability or fitness for particular purpose, good title and 
against infringement. 
The information in this manual contains only essential hardware concerns for general 
user and is subject to change without notice. Posiflex reserves the right to alter product 
designs, layouts or drivers without notification. The system integrator shall provide 
applicative notices and arrangement for special options utilizing this product. The user 
may find the most up to date information of the hardware from web sites: 
http://www.posiflex.com or http://www.posiflex.com.tw or http://www.posiflexusa.com 
All data should be backed-up prior to the installation of any drive unit or storage 
peripheral. Posiflex Technologies, Inc. will not be responsible for any loss of data 
resulting from the use, disuse or misuse of this or any other Posiflex product. 
All rights are strictly reserved. No part of this documentation may be reproduced, 
stored in a retrieval system, or transmitted in any form or by any means, electronic, 
mechanical, photocopying,  or otherwise, without prior express written consent  from 
Posiflex Inc. the publisher of this documentation. 

©

 Copyright Posiflex Technologies, Inc. 2008

 

All brand and product names and trademarks are the property of their respective holders.

 

KP-300 / KP-300T 

 SIDE MOUNT 

PROGRAMMABLE KEYPAD 

USER’S MANUAL 

Rev.: B0

P/N: 19830900030 

Summary of Contents for KP-300











Reviews: