background image

 

 

Part 16 

Emergency treatment: 

The battery is constructed maintenance free and leakproof. It is well 

protected in KS system as long as the ambient temperature remains below 
30

°

C and the ventilation of the KS system remains free. However, should any 

accident happen and the sulfuric acid from the battery spills on skin or clothing, 
wash immediately with water. If the acid comes in contact with eyes, rinse 
eyes with large amount of clean water and see a doctor immediately. A larger 
external battery may be connected to give an extended operation. Please check 
your dealer about this capability when required. 

WARNING: 

If there are any signs of over charging or leakage of electrolyte 

please contact your dealer immediately 

Power Supply 

The operating voltage range of the power adaptor should cover the 

local power supply for proper operation. The power cable, the power outlet 
and any power fusing arrangements must conform to local safety regulations. 

Please 

never do any connection / disconnection

 when system is still 

powered on. 

Please always keep the external power adaptor in a free air 

circulation. 

POWER ON/OFF 

Touch Open Cover 

A gentle tap on the touch open cover at 

left side of the main unit will open the cover and 
show the power switch, thumb wheel knob for 

brightness adjust and a PS/2 keyboard jack. It is 
preferable to keep this door closed through daily 
operation. The LCD brightness can also be 
controlled through software setting. Please note that some operating systems 
may inhibit the use of the PS/2 keyboard port if there is no device connected 
during boot up. 

There must always be at least 10 seconds waiting before switching on 

again once the system is powered off successfully. 

Power Indicator 

 

 

The power status of the system is indicated  by the backlight of the 

logo. When the logo lights in green, the AC power is standby for the system to 
turn on. The logo turns to blue when the system is powered on. 

Summary of Contents for KS - 6215N





















Reviews: