background image

 

 

Part 15 

USING THE TOUCH TERMINAL

APPLICATION ENVIRONMENT

It is 

very

 important that you check the following operational 

guidelines: 

Ventilation

This terminal must 

NOT

 be operated in an environment with 

restricted ventilation. There must be at least 25 mm air clearance around any 
top or side ventilation holes with a free flow of air around the unit at 

ALL

 

times for the installation. 

Operating Environment

The equipment must not be operated or stored in extremes of both 

temperature and humidity/moisture. (Operating range  0°C to 40°C and up to 
80% humidity – non condensing, max. wet bulb 26

C) 

UPS Battery (option)

General care:

The UPS battery is consumables beyond product warranty. Please 

definitely observe the alerts in beginning of this manual. If the equipment is to 

be powered off for more than few days, please always 

disconnect

 the battery 

from the system. Reconnect it and turn on the system to recharge the battery 
for 1 ~ 2 hours every 3 months for temperature lower than 30

C. Recharge for 

1 ~ 2 hours every month for temperature over 30

C. Temperature above 

40°C 

must be strictly avoided

 as it could cause termination of battery life and 

unexpected result even if the battery is not in work. The UPS battery can 
support basically the data preservation and smooth running of the system 
during intermittent or few minutes (30 min. up depending on loading and 
battery condition) power failure. 

Battery replacement:

When the UPS battery is installed, the user can install the utility 

Power Manager that will  interface the UPS battery monitor status with user. 
Find “PSW_vxxx” in the folder \drivers of the 
preloaded OS or search in the product information 
CD to install it. Please replace the used up UPS 
battery at power off whenever the message at the 
right appears. 

Emergency treatment:

The battery is constructed maintenance free and leakproof. It is well 

protected in  KS system as long as the ambient temperature remains below 
30

C and the ventilation of the KS system remains free. However, should any 

accident happen and the sulfuric acid from the battery spills on skin or clothing, 

Summary of Contents for KS - 6815





















Reviews: